Abit SM5 User Manual Download

Page: 22 / 96

2-14

Chapter 2

Installing Pipeline Burst SRAM

he SM5 mainboard features a 256K or 512K cache memory. It also features

a cache memory extension socket (COAST) in order to permit you to upgrade 256K
cache to 512K, and this with only one JP1 to choose from. Installation is very easy.
Refer to the table below:

Configuration

With 32K32

SRAM

With 64K32

SRAM

Cache socket

Cache total JP1 settings

Mode 1

OFF

Mode 2

YES

256K

OFF

Mode 3

YES

256K module

512K

Mode 4

256K module

256K

OFF

Mode 5

512K module

512K

Mode 6

YES

512K

OFF

【

Notes

】

1. If your mainboard features a 512K cache when it is delivered from the

factory (Mode 6 in the table), the mainboard will not have any cache
extension slot (COAST) or JP1 jumper.

2. The configurations listed in the table are all the possible configurations

reserved when the board was designed. The actual configuration when
the board is delivered depends mainly on the demands of the market.

3. The SM5-A mainboard do not support the cache extension slot

(COAST).

Summary of Contents for SM5

































































































Search results

Summary of Contents for SM5

Reviews:

Related manuals for SM5

Brands by name

Popular brands

Abit SM5, User Manual

Search results

Summary of Contents for SM5

Reviews:

Related manuals for SM5

Brands by name

Popular brands