Abit SM5 User Manual Download

Page: 41 / 96

Introduction of BIOS

3-13

BIOS Features Setup Menu

BIOS Features Setup Menu has already been set for maximum operation. If you

do not really understand each of the options in this menu, we recommend you use
default values.

In each item, you can press <F1> at any time to display all the options for this

item.

ROM PCI/ISA BIOS (XXXXXXXX)

BIOS FEATURES SETUP

AWARD SOFTWARE, INC.

Virus Warning

: Disabled

Video BIOS Shadow

: Enabled

CPU Internal Cache

: Enabled

C8000-CBFFF Shadow

: Disabled

External Cache

: Enabled

CC000-CFFFF Shadow

: Disabled

Quick Power on Self Test

: Enabled

D0000-D3FFF Shadow

: Disabled

Boot Sequence

: A,C, SCSI

D4000-D7FFF Shadow

: Disabled

Swap Floppy Drive

: Disabled

D8000-DBFFF Shadow

: Disabled

Boot Up Floppy Seek

: Disabled

DC000-DFFFF Shadow

: Disabled

Boot Up NumLock Status

: On

IDE HDD Block Mode

: Enabled

Typematic Rate Setting

: Enabled

Typematic Rate(Chars/Sec)

: 30

Typematic Delay (Msec)

: 250

Security Option

: Setup

PCI/VGA Palette Snoop

: Disabled

OS Select For DRAM > 64MB

: Non-OS2

Esc : Quit

↑↓→←

: Select Item

F1 : Help

PU/PD/+/- : Modify

F5 : Old Values

(Shift)F2 : Color

F6 : Load BIOS

Defaults

F7 : Load Setup

Defaults

Fig 3-3 BIOS Features Setup

Virus Warning:

This item can be set as Enable or Disable.

When this feature is enabled, if there is any attempt from a software or an
application to access the boot sector or the partition table, the BIOS will warn
you that a boot virus is attempting to access to the hard disk.

Summary of Contents for SM5

































































































Search results

Summary of Contents for SM5

Reviews:

Related manuals for SM5

Brands by name

Popular brands

Abit SM5, User Manual

Search results

Summary of Contents for SM5

Reviews:

Related manuals for SM5

Brands by name

Popular brands