Abit AB-BF6 Manual Download Page 47

Page: 47 / 106

Introduction of the BIOS

3-19

User’s Manual

Computer Knowledge: SHADOW

What is the SHADOW? The BIOS of standard video or interface cards is stored in

ROM, and it is often very slow. With the Shadow feature, the CPU reads the BIOS on

the VGA card and copies it into RAM. When the CPU runs this BIOS, the operation is

speeded up.

Delay IDE Initial (sec):

This item is used to support some old models or special types of hard disks or CD-ROMs.

They may need a longer amount of time to initialize and prepare for activation. Since the

BIOS may not detect those kinds of devices during system booting. You can adjust the value

to fit such devices. Larger values will give more delay time to the device. The minimum

number you can enter is 0, the maximum number you can enter is 15. The default setting is

Summary of Contents for AB-BF6











































































































Search results

Summary of Contents for AB-BF6

Reviews:

Related manuals for AB-BF6

Brands by name

Popular brands

Abit AB-BF6, Manual

Search results

Summary of Contents for AB-BF6

Reviews:

Related manuals for AB-BF6

Brands by name

Popular brands