Abit AB-BF6 Manual Download Page 20

Page: 20 / 106

2-10

Chapter2

BF6

JP1 Header: Disable or Enable Keyboard/Mouse Wake Up

This header is used to Disable or Enable

keyboard/mouse wake up function. This

function has to cooperate with the BIOS

setting (see section 3-5).

Short pin 1-2

Disable

keyboard/mouse

Wake Up

Short pin 2-3

Enable

keyboard/mouse

Wake Up (default)

JP2 Header: Disable or Enable Power Recovery

This header is used to Disable or Enable

power recovery function. This function has

to cooperate with the BIOS setting (see

section 3-5).

Short pin 1-2

Disable power recovery

Short pin 2-3

Enable

power

recovery

(default)

NOTE

If you enable the power recovery function and connect a ZIP device to the LPT port, you

have to turn off the power of your ZIP device after you shutdown your computer.

Otherwise, the onboard battery will run down.

CCMOS: CMOS Discharge Jumper

Jumper CCMOS discharge CMOS memory.

When you install the motherboard, make

sure this jumper is set for normal operation

(pin 1 and 2 shorted). See figure 2-6.

Summary of Contents for AB-BF6











































































































Search results

Summary of Contents for AB-BF6

Reviews:

Related manuals for AB-BF6

Brands by name

Popular brands

Abit AB-BF6, Manual

Search results

Summary of Contents for AB-BF6

Reviews:

Related manuals for AB-BF6

Brands by name

Popular brands