Abit AB-BF6 Manual Download Page 22

Page: 22 / 106

2-12

Chapter2

BF6

Note: Watch the power LED pin position and orientation.

PN1 (Pin 6-7): HDD LED Header

Attach the cable from the case’s front panel

HDD LED to this header. If you install it in

the wrong direction, the LED light will not

illuminate correctly.

Note: Watch the HDD LED pin position and

the orientation.

PN1 (Pin 8-9): Power on Switch Header

Attach the cable from the case’s front panel

power switch to this header.

PN1 (Pin 10-11): Hardware Suspend Switch (SMI Switch) Header

Attach the cable from the case’s front panel

suspend switch (if there is one) to this

header. Use this switch to enable/disable the

power management function by hardware.

Note: If you enable the ACPI function in the

BIOS setup, this function will not work.

PN2 (Pin 1-2): Hardware Reset Switch Header

Attach the cable from the case’s front panel

Reset switch to this header. Press and hold

the reset button for at least one second to

reset the system.

Summary of Contents for AB-BF6











































































































Search results

Summary of Contents for AB-BF6

Reviews:

Related manuals for AB-BF6

Brands by name

Popular brands

Abit AB-BF6, Manual

Search results

Summary of Contents for AB-BF6

Reviews:

Related manuals for AB-BF6

Brands by name

Popular brands