Abit AB-BF6 Manual Download Page 79

Page: 79 / 106

Install HighPoint XStore Pro Utility

B-1

User’s Manual

Appendix B Installing the HighPoint XStore Pro

Utility

We provide a useful and powerful utility in our product package,

HighPoint XStore Pro

What does XStore do? The XStore Pro is a hard disk enhancement utility which can improve

system performance. The basic concept is using a read-ahead caching algorithm to improve

the hard disk performance. With a market trend where most system’s standard

configurations are moving towards 48 MBytes memory size or beyond, HighPoint’s XStore

Pro provides higher system performance. XStore Pro is a new generation of XStore MMX

Accelerator for Storage.

XStore Pro utilizes the bigger system memory size to enhance memory management by

working with Windows

95 and 98. XStore Pro optimizes higher system performance by

read ahead caching after seeking, with large block sizes of hard disks. And best of all,

XStore Pro supports several PCI Bus Master Controllers such as Intel, SiS, Ali, Via and

others.

When you install XStore Pro, you can choose to install CD Xpress at the same time. Why do

you need CD Xpress? We’ll tell you more about it.

CD-ROM technology is growing fast, but its performance is still unacceptable compared to

today's hard drives. The transfer rates of today's hard drives can exceed 18MB/sec with

access times below 12ms. However, transfer rates for the fastest CD-ROM drives on the

market are below 2MB/sec with access times over 100 ms.

CD Xpress was created to accelerate the accessing speed of the CD-ROM drive by utilizing

the hard drive's high performance. CD Xpress reads and buffers data from the CD-ROM to

an area in the hard drive. With CD Xpress, when you access CD-ROM data, you are actually

accessing data from a swap file in the hard drive. This results in a tremendous increase in

CD-ROM performance without penalties.

Before you install this utility, there are several things you need to know.

Important Note

1. You can only install one Bus Master Driver at a time in your system, or the drivers will

result in conflict and cause system hangs. Please make sure you don’t have any Bus

Master Driver installed in your system before you install XStore Pro! You must remove

all components of the previous Bus Master Driver before you install XStore Pro to your

system. For example, you cannot install both the Intel

bus master driver and HighPoint

Summary of Contents for AB-BF6











































































































Search results

Summary of Contents for AB-BF6

Reviews:

Related manuals for AB-BF6

Brands by name

Popular brands

Abit AB-BF6, Manual

Search results

Summary of Contents for AB-BF6

Reviews:

Related manuals for AB-BF6

Brands by name

Popular brands