manualshive.com logo in svg

ABB UNO-DM-1.2-TL-PLUS, Manual

Share
Download
ABB UNO-DM-1.2-TL-PLUS Manual Download Page 66

- 66 -

000690CG

5 - Installation

I

nput connection to PV generator (DC side)

After having carried out preliminary checks and therefore having verified 

that there are no problems in the photovoltaic system, and the channel 

configuration has been selected (parallel or independent) you may con

-

nect the inputs to the inverter.

According to the system configuration, check the correct setting of the channels to indepen

-

dent or in parallel mode. An incorrect setting of the input channels can lead to loss of energy 

production.

Comply with the maximum input current relating to the quick-fit connectors as indicated in 

the technical data.

Polarity inversion can cause serious damage. Check polarity before connecting each string!

When the photovoltaic panels are exposed to sunlight they provide continuous DC voltage 

to the inverter. To avoid risks of electrical shock, 

all wiring operations must be carried out 

with the DC disconnect switch (internal and external to the inverter) and AC discon-

nect switches (external to the inverter) OFF.

Caution! The inverters referred to in this document are TRANSFORMERLESS. This type 

requires the use of insulated photovoltaic panels (IEC61730 Class A Rating) and the need to 

keep the photovoltaic generator floating with respect to ground: no terminal of the generator 

must be connected to ground.

For the string connections it is necessary to use the quick fit connectors 

(usually Weidmüller PV-Stick or WM4, MultiContact MC4 and Amphenol 

H4) located on the bottom of the mechanic 

 

09

.

09

Refer to the document “String inverter – Product Manual appendix” avai

-

lable at www.abb.com/solarinverters to know the brand and the model 

of the quick fit connector. Depending on the model of the connector of 

the own inverter, it is necessary to use the same model and the respec-

tive counterpart (check the compliant counterpart on the website of the 

manufacturer or in ABB)

Using corresponding parts that are not compliant with the quick fit connector models on the 

inverter could cause serious damage to the unit and lead to invalidation of the warranty.

Summary of Contents for UNO-DM-1.2-TL-PLUS







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands