manualshive.com logo in svg

ABB UNO-DM-1.2-TL-PLUS, Manual

Share
Download
ABB UNO-DM-1.2-TL-PLUS Manual Download Page 42

- 42 -

000682CG

3 - Characteristics

F

unctionality and components of the equipment 

Advanced web user interface

The UNO-DM-TL-PLUS inverters are equipped with a WLAN board 

IEEE802.11 b/g/n and with an web user interface that allow comission-

ing of the system, a full access to all main configuration and parame

-

ters of the inverter and can act as local monitoring solution. It can be 

accessed by using from any wireless capable device like laptop, tablet 

or smartphone via a common browser.

Aurora Vision Plant Management Platform

Aurora Vision is a cloud based platform enabling remote monitoring and 

asset management of ABB devices in range of solar power application.

Aurora Vision consists of a three different product:

1. 

Plant Portfolio Manager

 is a full featured web based application 

used by solar power professionals to monitor and manage a portfolio of 

solar power plants using ABB inverters.

2. 

Plant Viewer

 is an easy to use web based serviced application used 

by non-solar power professionals (such as homeowners or small busi-

ness owners) to monitor solar power plants they own.

3. 

Plant Viewer for Mobile

 is the mobile version of 

Plant Viewer

 en-

abling non-solar power professionals to remotely monitor their own PV 

plants by using smart phones, tablets and iPod Touch with IOS and An-

droid operating systems.

4. 

ABB Ability™ for solar plants - Energy Viewer 

is an easy to use 

mobile application allowing solar plant owners to remotely monitor all the 

energy flows and the performance of their own pv plants, with and with

-

out an energy storage system installed.

All product previously mensioned work toghether to allow solar power 

professional and site owners to collaboratively manage solar power plant.

Please contact the ABB tecnichal support for getting your own Plant Portfolio Manager account 

(mainly for installers and plant administrators). Please get your Plant Viewer, Plant Viewer for 

Mobile or Energy Viewer by accessing the website www.auroravision.net and click on “Regi

-

ster with Plant Viewer” button (mainly for site owners).

Summary of Contents for UNO-DM-1.2-TL-PLUS







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands