manualshive.com logo in svg

ABB UNO-DM-1.2-TL-PLUS, Manual

Share
Download
ABB UNO-DM-1.2-TL-PLUS Manual Download Page 167

- 167 -

001004AG

8 - Maintenance

10. Voltage absence test on DC side

Before to approach the below operations all the steps from1 to 9 included must be successfully 

completed.

 

 

Using the voltage detector, check the absence of voltage on the DC 

terminal connectors 

12

 between:

 

•

 

 

Each positive input and ground

 

•

 

 

Each negative input and ground

 

•

 

 

Positive input and negative input of each input section of the inverter.

DC INPUTS

-IN1 -IN1 +IN1 +IN1

+IN2 +IN2

-IN2 -IN2

12

11. Voltage absence test on AC side

 

 

Using the voltage detector, check the absence of voltage on the AC 

terminal connectors (lift the protective sheet to reach the connectors) 

between:

 

•

 

 

Phase to ground

 

•

 

 

Neutral to ground

 

•

 

 

Phase to neutral.

AC OUTPUTS

N

L

Summary of Contents for UNO-DM-1.2-TL-PLUS







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands