manualshive.com logo in svg

ABB UNO-DM-1.2-TL-PLUS, Manual

Share
Download
ABB UNO-DM-1.2-TL-PLUS Manual Download Page 177

- 177 -

000700CG

8 - Maintenance

- Code on display

- Error message 

- Signal

Name of Alarm and Cause

Solution

- E005

- Comm.Error

-   

Alarm LED

Communication error inside the inverter:

The alarm occurs when there are communication prob-

lems between the control devices inside the inverter.

• Error inside the inverter and cannot be checked externally. 

- If the problem (once the inverter has been switched off and 

back on) persists, contact customer assistance.

- E006

- Output OC

-   

Alarm LED

Output overcurrent:

The alarm occurs when the inverter's output current 

exceeds the inverter's threshold for maximum output 

current. 

• Error inside the inverter and cannot be checked externally. 

- If the problem (once the inverter has been switched off and 

back on) persists, contact customer assistance.

- E007

- IGBT Sat

-   

Alarm LED

Saturation recorded on the IGBT components:

The alarm occurs when one of the inverter's active de-

vices is in a saturated state.

Once the error occurs, the inverter tries to return to normal op-

eration.

- Should the error occur sporadically, it may be caused by a 

brusque transition of the grid voltage or of the input voltage, but 

is not due to a malfunction by the inverter.

- If the error is connected to an internal breakdown, it will con-

tinue to appear and so it is necessary to contact customer as-

sistance.

- E009

- Internal error

-   

Alarm LED

Error inside the inverter:

Error inside the inverter

• Error inside the inverter and cannot be checked externally.

- If the problem (once the inverter has been switched off and 

back on) persists, contact customer assistance.

- E010

- Bulk Low

-   

Alarm LED

Low “Bulk” voltage (DC-DC circuit):

The alarm may be triggered by causes external to the 

inverter: a reduced input voltage on the inverter (just 

above the activation voltage) but which is not accom-

panied  by  a  sufficient  availability  of  power  from  the 

photovoltaic generator (typical condition of the stages 

with limited irradiation) 

- If the error signal occurs sporadically, it may be due to causes 

external to the inverter (limited irradiation and so limited power 

availability from the PV generator).

- If the problem occurs systematically also in conditions of high 

irradiation and with input voltage which is significantly higher 

than the activation voltage, contact customer assistance.

- E011

- Ramp Fail

-   

Alarm LED

Long wait for “Booster” regime to start:

Error internal to inverter relating to start up time for DC-

DC circuit regime (Booster)

• Error inside the inverter and cannot be checked externally.

- If the problem (once the inverter has been switched off and 

back on) persists, contact customer assistance.

- E012

- DcDc Fail

-   

Alarm LED

Error in the “Booster” circuit (DC-DC side) record-

ed by the “Inverter” circuit (DC-AC side):

Error internal to inverter relating to operation of the DC-

DC circuit regime (Booster)

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

- E013

- Wrong Mode

-   

Alarm LED

Incorrect  configuration  of  inputs  (set  in  parallel 

rather than independent):

The alarm is generated solely when the inverter is con-

figured with parallel inputs. In this particular configu

-

ration the inverter checks the input voltage of each of 

the two channels and if the two voltages differ by more 

than 20Vdc, the alarm is raised .

• Check that the setting of the "IN MODE" switch is specifically 

set to "PAR" and that the bridges between the two input chan-

nels have been included.

- If the configuration of the inverter is correct, check that the 

input strings have the usual number of standard panels of the 

usual brand and with the same inclination/orientation.

- If both the configuration of the inverter and the characteristics 

of the PV generator conform with the specifications, contact 

customer assistance.

- E014

- Over Temp.

-   

Alarm LED

Excessive temperature inside the inverter:

External temperature over 60°C. This parameter also 

depends on the power which the inverter must supply 

since the measurement of temperatures is done inter-

nally and is influenced by the heat dissipated by the 

components of the inverter itself

• Check that the inverter is not exposed to direct sunlight. Wait 

for the temperatures to which the inverter is exposed to return 

to the operating range and for the inverter to cool down.

- If the problem (once the ambient temperature has returned to 

the range) persists, contact customer assistance. Remember 

to wait the time needed to allow the inverter to cool down

- E015

- Bulk Cap Fail

-   

Alarm LED

Fault recorded on the “Bulk” capacitor:

Error inside the inverter relating to a problem in the bulk 

capacitors.

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

- E016

- Inverter Fail

-   

Alarm LED

Error in the “Inverter” circuit (DC-AC side) record-

ed by the “Booster” circuit (DC-DC side):

The alarm is generated when a problem is recorded in 

the inverter circuit (DC/AC)

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

- E017

- Start Timeout

-   

Alarm LED

Long wait for “Inverter” regime to start up:

Error internal to inverter relating to start-up time for the 

DC-AC circuit regime (Inverter)

• The alarm may be triggered by causes external to 

the inverter: a reduced input voltage on the inverter 

(just above the activation voltage) but which is not ac-

companied by a sufficient availability of power from the 

photovoltaic generator (typical condition of the stages 

with limited irradiation) 

- If the error signal occurs sporadically, it may be due to causes 

external to the inverter (limited irradiation and so limited power 

availability from the PV generator).

- If the problem occurs systematically also in conditions of high 

irradiation and with input voltage which is significantly higher 

than the activation voltage, contact customer assistance.

Summary of Contents for UNO-DM-1.2-TL-PLUS







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands