manualshive.com logo in svg

ABB Sensyflow iG, Operating Manual, Page: 46 / 60

Share
Download
ABB Sensyflow iG Operating Manual Download Page 46

Operation, configuration and communication

46

Sensyflow iG, Version 1.00

42/14-39 EN

Submenu level 2 

→

 AI FLOW MENU

 

Display indication

Designation according to 
PA profile 3.0

Explanation

AI FLOW STATE

AI FLOW STATE

D

Display of status message for mass flow in hexadecimal notation (status to AI Flow Block)

Display 0x80 … 0x83 

→

 OK 

(

see section 7.1.2.2 

and 

see section 7.1.2.3 

)

FLOW PV_SCALE HIGH
PV_SCALE_HIGH

SE

internal 100 % value, normally upper range value

FLOW PV_SCALE LOW

PV_SCALE_LOW

SE

internal 0 % value, normally lower range value

OUT_SCALE AT 100%

OUT_SCALE_AT 100%

SE

external 100 % value

OUT_SCALE AT 0%
OUT_SCALE_AT 0%

SE

external 0 % value

FLOW FAILSAFE TYPE

FSAFE_TYPE

SP

If the device detects an error by means of the status signal, one of the following two options can be 
selected for the output FLOW signal:
LAST VALID VALUE the last valid measuring value

ERROR VALUE the current measuring value

ERROR SUBSTITUTION VALUE a selectable replacement value

FLOW FAILSAFE VALUE
FSAFE_VALUE

SP

Arbitrary numeric value as substitution for an incorrect measuring value. This is only sent to the out-
put if option ERROR SUBSTITUTION VALUE has been selected in FLOW ERROR SIGNAL.

FLOW  FILTER FACTOR

PV_FTIME

SP

Filter factor for signal attenuation, adjustable between 0.2 s and 100 s

FLOW  HYSTERESIS

ALARM_HYS

SP

Hysteresis for limit value monitoring, input in the selected mass flow unit (e. g. 1 kg/h)

FLOW ALARM HIGH
HI_HI_LIM

SP

Upper alarm limit; alarm is triggered if measuring value exceeds limit

FLOW WARNING HIGH

HI_LIM

SP

Upper warning limit (pre-alarm); warning is issued if measuring value exceeds limit

FLOW WARNING LOW

LO_LIM

SP

Lower warning limit (pre-alarm); warning is issued if measuring value falls below limit

FLOW ALARM LOW
LO_LO_LIM

SP

Lower alarm limit; alarm is triggered if measuring value falls below limit

FLOW SIMULATION

SIMULATE

SP

Outputting FLOW simulation values ON or OFF
(incl. STATUS QUALITY and STATUS LIMIT) 
(Note: ON produces the symbol "S" in the display)

FLOW SIMUL. VALUE

SP

Input of the flow simulation value

STATUS QUALITY

SP

Simulation of the STATUS signal, selection from the signals described in section 

 7.1.2.2 

and 

 7.1.2.3 

GOOD OK, 

GOOD UPDATE EVENT…

STATUS LIMIT

SP

Simulation of the limit value STATUS, selection between
OK

LOW_LIMIT

HIGH_LIMIT
CONSTANT 

END AI FLOW

Summary of Contents for Sensyflow iG





























































Reviews:

No comments