manualshive.com logo in svg

ABB Sensyflow iG, Operating Manual, Page: 44 / 60

Share
Download
ABB Sensyflow iG Operating Manual Download Page 44

Operation, configuration and communication

44

Sensyflow iG, Version 1.00

42/14-39 EN

Submenu level 1 

→

 PROFIBUS MENU 

Submenu level 1 

→

 SERVICE MENU

Display indication

Explanation

TB FLOW MENU

Access to the Transducer Block Flow (mass flow) in submenu 
level 2 

AI FLOW MENU

Access to the Analog Input Block Flow (mass flow) in submenu 
level 2 

TB GAS TEMP MENU

Access to the Transducer Block Gas Temperature in submenu 
level 2 

AI GAS TEMP MENU

Access to the Analog Input Function Block Gas Temperature in 
submenu level 2 

TOTAL MENU

Access to the Function Block Totalizer (integrator) in submenu 
level 2 

END PROFIBUS MENU

Display indication

Explanation

MAX. VALUES

D

Indication of the maximum mass flow and gas temperature va-
lues since commissioning

MIN. VALUES

D

Indication of the minimum mass flow and gas temperature va-
lues since commissioning

DEVICE TEMP.

MAX TEMP.

D

Indication of current housing temperature

Indication of maximum housing temperature value since com-
missioning

CAL. DATE

TIME

D

Indication of date of last calibration

Indication of device operating hours (operating hour meter)

(Display format: Years: days: hours: minutes)

STATUS FLOW

TEMP     TOT

D

Indication of status messages for mass flow, gas temperature 
and integrator in hexadecimal notation. 

Display 0x80 … 0x83 

→

 OK 

(

see section 7.1.2.2 

 and 

see section 7.1.2.3 

)

DIAG  1…4

D

Display of diagnostic bytes 1 to 4

Display 0x80 … 0x83 

→

 OK 

(

see section 7.1.3 

)

DIAG  5…8

D

Display of diagnostic bytes 5 to 8

Display 0x80 … 0x83 

→

 OK 

(

see section 7.1.3 

)

END SERVICE MENU

Summary of Contents for Sensyflow iG





























































Reviews:

No comments