manualshive.com logo in svg

ABB Sensyflow iG, Operating Manual, Page: 15 / 60

Share
Download
ABB Sensyflow iG Operating Manual Download Page 15

Mechanical installation

42/14-39 EN

Sensyflow iG, Version 1.00

15

4.4 Mounting the evaluation electronics (remote version)

In the remote version you can use cables with a length up to 25 m between sensor (transducer) and eva-
luation electronics. The transducer is installed as described before in the pipe component or weld-on ad-
apter. The evaluation electronics is then mounted with the mounting plate – observing the maximum
permissible ambient temperature – to an even wall surface (

see Fig. 4-5

 for dimensions).

Fig. 4-5 Dimensions of the Sensyflow iG mounting plate ( Remote-Version)

Due to the rotating housing head the rear terminal box is still accessible. 

The connection between sensor and evaluation electronics is made via 10-pole, numbered terminal
blocks that can be accessed after removing the covers at the sensor connection housing and the terminal
box of the electronics unit.
 

 

(dimensions in mm)

Mounting plate

Sensor

connection housing

100

Z-20275

07

112

Summary of Contents for Sensyflow iG





























































Reviews:

No comments