ABB PCS6000 User Manual Download Page 37

Page: 37 / 114

PRODUCT DESCRIPTION

PRODUCT

PCS6000

DOCUMENT KIND

User manual

DOCUMENT ID.

3BHS600000 E40

REV.

LANG.

PAGE

37/114

3.2.4. Water cooling unit (WCU)

The main tasks of the WCU are:

– Ensuring constant water pressure, flow and temperature

– Interfacing to the external heat exchanger equipment

– De-aeration of cooling water circuit

– De-ionizing the cooling water

A soft starter for the cooling pumps is available as option.

The WCU can be specified for connection of the external heat exchanger on the top
(standard) or bottom.

The WCU varies depending on the converter size.

Figure 3–13 WCU (typical design)

1) Inlet from re-cooler on top
2) Expansion vessel (optional)
3) Cooling water pump 1
4) Outlet to re-cooler on top

5) Interface box to control
6) Ion exchanger vessel
7) Cooling water pump 2 (optional)

Summary of Contents for PCS6000



















































































































Search results

Summary of Contents for PCS6000

Reviews:

Brands by name

Popular brands

ABB PCS6000, User Manual

Search results

Summary of Contents for PCS6000

Reviews:

Brands by name

Popular brands