background image

 

2TLC172315M0201, rev K 

www.abb.com/jokabsafety 

Monday, May 07, 2018 10:51:13 AM 

Please read and familiarize yourself with the contents of this user 
manual. 

Please read and familiarize yourself with the contents of this user manual before starting to use the products. 
Please contact your ABB JOKAB SAFETY representative if you have any questions or comments. 

GUARANTEE 

ABB JOKAB SAFETY guarantees that the products are free from material or performance defects for one (12) 
months (or other period if stated) from date of purchase from ABB JOKAB SAFETY. 

ABB JOKAB SAFETY DISCLAIMS GUARANTEES OF ALL KIND, EXPRESSED OR IMPLIED, ON NON 
INFRINGEMENT, SALEABILITY OR SUITABILITY FOR CERTAIN PURPOSES WHERE THE BUYER OR USER 
ALONE DETERMINES WHETHER THE PRODUCTS MEETS THE REQUIREMENTS OR ARE SUITABLE FOR A 
SPECIFIC PURPOSE. ABB JOKAB SAFETY OFFERS NO ADDITIONAL GUARANTEES, EITHER EXPRESSED 
OR IMPLIED 

LIMITATION OF LIABILITY 

ABB JOKAB SAFETY DISCLAIMS LIABILITY FOR SPECIFIC, INDIRECT OR CONSEQUENTIAL DAMAGE, 
LOSS OF REVENUE OR BUSINESS OF ANY KIND IN RELATION TO THESE PRODUCTS, IRRESPECTIVE OF 
SUCH A CLAIM BEING BASED ON AN AGREEMENT, GUARANTEE, CARELESSNESS OR PURE LIABILITY. 

Under no circumstances, can ABB JOKAB SAFETY's liability exceed the cost of the individual product for which 
liability is cited. 

ABB JOKAB SAFETY IS NOT LIABLE UNDER ANY CIRCUMSTANCES FOR ANY GUARANTEE, REPAIR OR 
OTHER CLAIMS WITH REGARD TO THE PRODUCTS IF ABB JOKAB SAFETY’S ANALYSIS CONFIRMS THAT 
THE PRODUCTS HAVE NOT BEEN CORRECTLY HANDLED, STORED, INSTALLED OR MAINTAINED OR 
SUBJECTED TO DAMAGE, INCORRECT USAGE OR INAPPROPRIATE MODIFICATION OR REPAIR. 

PRODUCT SUITABILITY 

ABB JOKAB SAFETY is not liable for compliance with standards, regulations or directives that apply for product 
combinations in the customer's application or product usage. ABB JOKAB SAFETY will supply, on customer 
request, certification documents from a third party with data on classification and usage limitations for the products. 
This information is not in itself sufficient for a complete assessment of the suitability of the products in combination 
with the end product, machinery, system or other application or usage. 

Please see below several examples of application areas where particular attention must be observed. This is not a 
complete list of all possible application areas for the products, nor is it claimed that the application areas named are 
suitable for the products in question: 

Outdoor use, application areas that entail risk of chemical contamination or electric shocks or conditions or 
application areas that are not described in this manual. 

Control systems for nuclear power, combustion systems, railway systems, aviation systems, medical equipment, 
slot machines, vehicles and installations that are subject to separate industry directives or national regulations. 

Systems, machinery and equipment that can comprise danger to life or property. 

Check and take note of all prohibited application areas for the products. 

NEVER USE THE PRODUCTS IN AN APPLICATION THAT ENTAILS SERIOUS DANGER TO LIFE OR 
PROPERTY WITHOUT FIRST ASCERTAINING THAT THE SYSTEM AS A WHOLE IS DESIGNED TO MANAGE 
SUCH RISKS, AND THAT THE PRODUCT FROM ABB JOKAB SAFETY HAS THE RIGHT CLASSIFICATION 
AND IS PROPERLY INSTALLED FOR THE USE INTENDED AS PART OF EQUIPMENT OR SYSTEMS. 

PERFORMANCE INFORMATION 

Even though everything has been done to ensure the veracity of the information in this manual, 
ABB JOKAB SAFETY disclaims liability for errors or omissions and reserves the right to make changes and 
improvements without prior notice. The information on product performance provided in this manual is intended for 
guidance purposes only for the user when assessing the product's suitability and does not comprise any guarantee. 
This can concern tests performed by ABB JOKAB SAFETY and the user must observe the requirements for the 
application intended. For actual performance, please see the wording in ABB JOKAB SAFETY's Guarantee and 
Limitation of Liability. 

 

 

Summary of Contents for Magne 3 Series



























Reviews: