manualshive.com logo in svg

ABB J2007003L301A, Quick Start Manual

Share
Download
ABB J2007003L301A Quick Start Manual Download Page 18

 

 

Page 18

 

© 2021 ABB. All rights reserved.

 

 

Version 1.0

 

Spare List

 

Power Modules

 

Ordering code

 

Description

 

Application

 

CC109165610 

 

     EP1600

-

UTEZ RECTIFIER 

 

48 

-

 58V, 24A  AC/DC Rectifier Module

 

150027362

 

PE 8CKT LMT MODULE

 

-

48V unregulated Converter Module

 

Controller Modules

 

150038227

 

SPS841A_0I6R_USB_DS CONTROLLER 

 

Controller

 

150027361 

 

PE ALARM CARD

 

Controller Alarm Card

 

Ship Loose Material

 

Ordering code

 

Description

 

Application

 

CC408578578

 

SCREW MCH #10

-

32 HEX HEX SL CONE LCK STEEL 

Module Mounting Provisions

 

CC408577571 

 

SCREW TAP #12

-

24 HEX WSH HEX SL STEEL ZINC

-

CLEAR 

 

Module Mounting Provisions

 

450026710

 

TB 1850741 FRONT

-

MC 1,5/10

-

ST

-

3,81 8A 160V 10

-

POS 

 

10

-

pin Connector

 

4600417774P 

 

CONNECTOR 5.08MM PITCH 3POS 16A 300V 

 

3POS AC Input mating connector

 

Table 8:  Spares Listing

 

Specifications and ordering information are in the Power Express Class 2 Distribution Brochure available at

 

 

abbpowerconversion.com

 

• 

External Surge Protective Device (SPD) is required on all AC inputs. 

 

• 

Equipment and subassembly ports: 

 

1.     are suitable for connection to intra

-

building or unexposed wiring or cabling

 

2.     can be connected to shielded intra

-

building cabling grounded at both ends. 

 

• 

Grounding / Bonding Network –

 

Connect to an Isolated Ground Plane (Isolated Bonding Network) or an Integrated Ground 

Plane (Mesh Bonding Network or Common Bonding Network). 

 

• 

Installation Environment 

-

 Install in Network Telecommunication Facilities, OSP, or where NEC applies. 

 

• 

Battery return may be either Isolated DC return (DC

-

I) or Common DC return (DC

-

C). 

 

• 

External  Surge  Protective  Devices  (SPDs) 

-

  are  required  on  all  AC  inputs.  Equipment  Safety  is  Approved  in  IEC  60664

-

1 

Installation Category II environments. 

 

• 

DC Returns 

-

 Isolated DC return (DC

-

I) or Common DC return (DC

-

C). 

 

Specifications and Applications

 

QUICK START GUIDE

 

Information –

 

Converter Module Basic Information

 

Converter

 

Input 

 

Recommended 

Fuse

 

Per Output 

 

Vdc

 

A 

 

A

 

Vdc

 

VA

 

A

 

150027362

 

PE 8CKT LMT MODULE

 

-

40 to 

-

60

 

20

 

25

 

-

42 to 

-

58

 

100

 

2.38 Max

 

Table 7:  Converter Data

 

Note: Each converter provide 8 outputs 

 

Summary of Contents for J2007003L301A





















Reviews:

No comments

Brands by name

Popular brands

Load more brands