ABB 80307300R Operation Manual Download

Page: 97 / 122

Operation Manual / 4 Product description / A130-H.. - A140-H

8 Dismantling and fitting / 8.8 Removing the cartridge group

HZTL4030_EN

Revision D

May 2017

8.8

Removing the cartridge group

Fig. 33: Removing insulation sheets

If present: Remove the insulation sheets (01, 02, 03).

Mark the casing position for assembly.

Do not remove oil orifice (if present)

To limit the oil flow rate through the bearing casing during operation (engine under load) to
the admissible values, an oil orifice is mandatory at the oil inlet of the bearing casing if the
oil inlet pressure is > 3 bar (overpressure).

If an oil orifice is fitted in the oil inlet of the bearing casing, it must not be removed.

Fig. 34: Oil orifice

01 Bearing casing
02 Oil orifice
03 Circlip

Page

All manuals and user guides at all-guides.com

Summary of Contents for 80307300R



























































































































Search results

Summary of Contents for 80307300R

Reviews:

Related manuals for 80307300R

Brands by name

Popular brands

ABB 80307300R, Operation Manual

Search results

Summary of Contents for 80307300R

Reviews:

Related manuals for 80307300R

Brands by name

Popular brands