ABB 80307300R Operation Manual Download

Page: 81 / 122

Operation Manual / 4 Product description / A130-H.. - A140-H

7 Eliminating malfunctions / 7.2 Malfunctions during operation

HZTL4030_EN

Revision D

May 2017

Exhaust gas temperature too high

Engine performance and engine speed unchanged

Possible causes

Remedy

Turbocharger

Insufficient air, for example, when
filter silencer is blocked by contam-
ination

Clean (see chapter

Periodic mainten-

ance work

→

)

Compressor/turbine contaminated

Exhaust gas back pressure too high Clean or repair boiler or exhaust gas si-

lencer

Turbine damaged or eroded

Contact ABB Turbocharging Service
Station

Engine

Malfunction in the injection system Repair or contact manufacturer

Charge air
cooler

Cooler contaminated

Clean

Cooling water volume too low

Fill

Inlet temperature of cooling water
too high

Check/clean cooling system

Insufficient ventilation

Improve ventilation

Table 18: Malfunctions during operation – Exhaust gas temperature too high

Charge air pressure too low

Engine performance and engine speed unchanged, suction condition normal

Possible causes

Remedy

Turbochar-
ger

Manometer display not correct

Replace manometer

Supply pipe to manometer not sealed Repair leak

Filter silencer contaminated, therefore
pressure drop too high

Clean (see chapter

Periodic mainten-

ance work

→

)

Compressor end and/or turbine end
contaminated

Compressor/turbine damaged

Contact ABB Turbocharging Service
Station

Exhaust gas back pressure too high

Clean or repair boiler or exhaust gas
silencer

Engine

Air receiver not sealed

Repair

Gas piping between engine and tur-
bine leaking

Injection mistimed

Set correctly

Valve control misadjusted

Pipes

Pipes downstream to the compressor
outlet not sealed.

Repair.

Table 19: Malfunctions during operation – Charge air pressure too low

Page

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for 80307300R



























































































































Search results

Summary of Contents for 80307300R

Reviews:

Related manuals for 80307300R

Brands by name

Popular brands

ABB 80307300R, Operation Manual

Search results

Summary of Contents for 80307300R

Reviews:

Related manuals for 80307300R

Brands by name

Popular brands