ABB 80307300R Operation Manual Download

Page: 103 / 122

Operation Manual / 4 Product description / A130-H.. - A140-H

8 Dismantling and fitting / 8.13 Installing nozzle ring

HZTL4030_EN

Revision D

May 2017

8.13

Installing nozzle ring

Fig. 41: Installing the nozzle ring

*) Variant A1 or A2, depending on the nozzle ring version.

1. Fit the lamellar sealing ring (56005) in the correct slot (see detail A1/A2). When doing

this, pay attention to correct winding of the lamellar sealing ring (see detail B).

2. Secure the lamellar sealing ring (56005) with adhesive tape (01).

3. Place the burst ring (57210) in the turbine casing.

4. Insert the nozzle ring (56001) (with the cams facing downwards) into the turbine casing

as far as it will go. Align the cams on the nozzle ring with the recesses of the turbine cas-
ing (51000). Do not remove the adhesive tape (01).

5. If present: Fit the metal C-ring (51105).

Page

All manuals and user guides at all-guides.com

Summary of Contents for 80307300R



























































































































Search results

Summary of Contents for 80307300R

Reviews:

Related manuals for 80307300R

Brands by name

Popular brands

ABB 80307300R, Operation Manual

Search results

Summary of Contents for 80307300R

Reviews:

Related manuals for 80307300R

Brands by name

Popular brands