ABB 80307300R Operation Manual Download

Page: 19 / 122

Operation Manual / 2 Safety / A130 - A155

1 Safety / 1.10 Lifting of loads

HZTL4022_EN

Revision E

May 2017

1.10

Lifting of loads

WARNING

Suspended loads

Loads that are not attached according to regulations can cause injury to
personnel or fatal accidents.

Loads must always be fastened to properly functional lifting gear with a
sufficient load limit.

Pay attention to the correct attachment of loads on the crane hook.

People must not stand beneath suspended loads.

Wear safety gloves to protect against mechanical hazards.

Wear safety helmet.

Fig. 3: Attachment of loads on the crane hook

Fig. 4: Attachment angle

If there are two or more suspension points, the attachment angle of 45° must not be ex-
ceeded. This prevents excessive loading due to diagonal pull.

Before looping around the components of the turbocharger, let them cool down (max-
imum 80 °C).

Attach components of the turbocharger as described in the respective action steps.

Use a suitable edge guard if there are sharp edges.

The assembly devices must be completely screwed in and must not unscrew during use.

Use assembly devices only for the described applications.

Put down dismantled components of the turbocharger in such a way that they cannot tip
over.

Page

All manuals and user guides at all-guides.com

Summary of Contents for 80307300R



























































































































Search results

Summary of Contents for 80307300R

Reviews:

Related manuals for 80307300R

Brands by name

Popular brands

ABB 80307300R, Operation Manual

Search results

Summary of Contents for 80307300R

Reviews:

Related manuals for 80307300R

Brands by name

Popular brands