ABB 80307300R Operation Manual Download

Page: 77 / 122

Operation Manual / 4 Product description / A130-H.. - A140-H

6 Periodic maintenance work / 6.2 Cleaning components mechanically

HZTL4030_EN

Revision D

May 2017

WARNING

Heating up of cleaning agents and operating fluids

When cleaning agents or operating fluids are heated up, explosive vapours
can be produced which are hazardous to health.

Observe the information in the material safety data sheet.

Wear a respiratory mask according to material safety data sheet.

CAUTION

Water and contamination in the cartridge group

If water or contamination penetrates the cartridge group, this can impair
the function of the turbocharger and damage parts inside the cartridge
group.

Place the cartridge group on suitable supports (01) made of wood or
metal.

Observe dimension (B) for the supports (01) so that the cartridge group
is not immersed too deeply.

Let the layers of contamination on the turbine soak for four hours.

Removing dirt

WARNING

Health hazard due to soot particles

If soot particles enter the eyes or respiratory tract, this can be harmful to
health.

Avoid the formation of dust.

Vacuum up dust with a suitable vacuum cleaner.

Wear a respiratory mask to protect against particles (P1 or P2 mask).

Wear safety goggles.

Wear a respiratory mask to protect against dusts.

Wear safety gloves to protect against mechanical hazards.

Lift up the cartridge group and align it horizontally.

Remove dirt manually using a soft brush or a wire brush.

Page

All manuals and user guides at all-guides.com

Summary of Contents for 80307300R



























































































































Search results

Summary of Contents for 80307300R

Reviews:

Related manuals for 80307300R

Brands by name

Popular brands

ABB 80307300R, Operation Manual

Search results

Summary of Contents for 80307300R

Reviews:

Related manuals for 80307300R

Brands by name

Popular brands