ABB 80307300R Operation Manual Download

Page: 42 / 122

Operation Manual / 4 Product description / A130-H.. - A140-H

2 Removing and Installing / 2.2 Removing the turbocharger

HZTL4030_EN

Revision D

May 2017

2.2.3

Positioning the turbocharger for storage

WARNING

Risk of tipping

If the turbocharger is not positioned stably, it may tip over. This can result in
serious personal injury.

Place the turbocharger on a clean, level support.

Secure the turbocharger to prevent it from tipping over by using wooden
beams and wedges and by taking the centre of gravity into account.

Fig. 8: Putting down the turbocharger

Remove turbocharger from engine support, set it down properly in an appropriate place
and secure it.

Close or cover the openings of the turbocharger and support.

Page

All manuals and user guides at all-guides.com

Summary of Contents for 80307300R



























































































































Search results

Summary of Contents for 80307300R

Reviews:

Related manuals for 80307300R

Brands by name

Popular brands

ABB 80307300R, Operation Manual

Search results

Summary of Contents for 80307300R

Reviews:

Related manuals for 80307300R

Brands by name

Popular brands