background image

41-001524-00 REV01 – 07.2014

171

Troubleshooting Solutions

Why is my display blank?

Ensure that power is being provided to your phone. If your network does not provide inline power over Ethernet, you can 
obtain an additional accessory, the Aastra PoE (Power over Ethernet) inline power supply, to provide power over Ethernet 
locally to your phone. See the 

Connecting to the Network and to Power 

section

 

in the 

Aastra 6867i Installation Guide

 

for details. 

Why is my speakerphone not working?

If you press the 

 button and the speaker light flashes and you do not hear dial tone through the speaker, the 

Audio 

Mode 

option in the phone has been set up for headset use. Press 

 a second time and if the light goes out, the 

phone has been set up to be used only with a headset or handset. If the light stays on steady and you hear a dial tone, the 
phone has been set up so that you can alternate between the speakerphone and the headset by pressing 

. See 

“Audio Mode”

 on 

page 45

 for instructions on how to change the 

Audio Mode

 option.

Why can’t I get a dial tone?

Check for any loose connections and that the phone has been installed properly. For installation instructions, please refer 
to the 

Installation and Setup

 section in the 

Aastra 6867i Installation Guide

.

Why doesn’t my phone ring?

Check the ring volume on your phone. It may be turned down or turned off. To adjust the ringer volume setting, press the 
volume button when the phone is on-hook and idle.

Why is the light not coming on with a new voicemail message?

Your phone system or service provider must provide the visual message waiting service for this function to work. Check 
with your System Administrator for more information.

Why is my handset not working?

Check to ensure that the handset cord is fully connected to both the phone and handset. See the 

Connecting a Handset 

or Headset

 section in the 

Aastra 6867i Installation Guide

 for information.

How do I find the IP address of my phone?

Instructions on where to find the IP address of your phone can be found in 

“Finding Your Phone’s IP Address”

 on 

page 25

.

Why does my phone display the No Service message?

The phone displays the 

No Service

 message if the SIP settings have not been set up correctly. Contact your System 

Administrator for more information.

How do I change my user password?

You can change the user password from the IP phone UI or the Aastra Web UI. See 

“Password”

on 

page 40

 and 

“Configuring 

Lock Settings Using the Aastra Web UI”

on 

page 42 

for more information.

Why does my phone display Bad Encrypted Config?

The IP phone displays 

Bad Encrypted Config

 because encrypted configuration files are enabled but the decryption proc-

ess has failed. Report this error to your System Administrator.

Summary of Contents for 6867i






























































































































































































Reviews: