A.R.C. Laser FOX 514 User Manual Download Page 44

Page: 44 / 56

User Manual FOX 514

September 2021

File: User Manual_FOX 514_rev3

8.5.2 Troubleshooting

The following errors cannot be identified by the system self check and have to be checked
by the user:

Problem

Potential Error

Troubleshooting

Error Message: F01

Battery is empty

Connect the laser to the mains and
restart it.

Screen is black

Laser is in Sleep mode

As a standard, the laser enters
the power save mode after 5
min of inactivity. Touch the
display or a blue arrow-key to
activate the device.

No aiming beam visible

Laser is in Stand-By mode

The aiming beam is only visible
when the laser is in READY
mode. Switch the laser to READY
mode

Aiming beam brightness
set too low

Increase the parameter for
aiming beam brightness

Fiber is not properly inserted

Twist the fiber connector inside the
socket with a light movement in
wards

Fiber is broken

Replace the broken fiber with a
new one

Aiming beam - diode defective

Contact your A.R.C. Laser
representative

No laser beam but aiming
beam visible

Foot switch non plugged in

Check if foot switch is correctly
plugged in

Foot switch defective

Contact your A.R.C. Laser
representative

No aiming beam and no laser
beam visible

Fiber optic is not connected
to laser or not correctly
plugged in

Check the correct fitting of the
fiber or hand piece

Fiber is broken

Replace the broken fiber with a
new one

Summary of Contents for FOX 514

























































Search results

Summary of Contents for FOX 514

Reviews:

Related manuals for FOX 514

Brands by name

Popular brands

A.R.C. Laser FOX 514, User Manual

Search results

Summary of Contents for FOX 514

Reviews:

Related manuals for FOX 514

Brands by name

Popular brands