A.R.C. Laser FOX 514 User Manual Download Page 31 | Manualshive

Page: 31 / 56

background image

User Manual FOX 514

September 2021

File: User Manual_FOX 514_rev3

31

6.3 Programs and Settings

6.3.1 Display / Main Menu

6.3.2 Saving parameters

How the parameters for power / pulse length / pulse interval can be changed is described in
the following three sections.

To store the modified parameters, please press the plus and minus buttons for adjusting the
aiming beam brightness for a few seconds. The saved parameters are stored as basic setting
when the device is switched on again.

6.3.3 Power settings

The power can be set by using the rotary wheel. Doing so,
the color of the value changes from black to white. In this
case, the font color of the power changes from black to white.
This color scheme can also be reversed if desired. For a
description see chapter 6.4.3.2.

The displayed value may vary from the emitted value at the
distal tip, by a range of ±20%.

Reset Button

Settings

Power

Pulse counter

Pulse pause

Modify

values using the

arrows on the right

Pulse length

Decrease or increase of
chosen values using the
arrows on the left

Battery mode

Aiming beam brightness

Decrease or increase of brightness
when fiber is inserted using the
circular plus and minus buttons

«
...
29
30
31
32
33
...
»

Summary of Contents for FOX 514

























































Reviews:

No comments

Related manuals for FOX 514

Brand: rainforest Pages: 2

Brand: WAGER Pages: 22

Brand: Kane Pages: 4

Brand: B meters Pages: 18

Brand: B meters Pages: 14

Brand: M-Sure Pages: 2

Brand: Wavetronix Pages: 14

Brand: Danfoss Pages: 80

Brand: Dräger Pages: 538

Brand: Bahco Pages: 21

Brand: Kübler Pages: 72

Brand: Bartec Pages: 38

Brand: LORECa Hearing Instrument Pages: 43

Brand: Hanna Instruments Pages: 24

DistanceMaster Compact

Brand: LaserLiner Pages: 14

Brand: inbody Pages: 36

Brand: Megasat Pages: 25

Brand: Thermocable Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands