6Harmonics GWS-3000 Operating Manual Download Page 3

Page: 3 / 31

7.22 cu command........................................................................................................................... 25

7.23 cd command.......................................................................................................................... 25

7.24 setagcmode command .......................................................................................................... 25

7.25

getagcmode command ......................................................................................................... 26

7.26 setrxatten command................................................................................................................ 26

7.27 getrxatten command.............................................................................................................. 27

7.28 reboot command .................................................................................................................... 27

8 Power Control and Link Configuration............................................................................................. 27

8.1 Manual Power Control................................................................................................................ 27

8.1.1

Point to Point Link ........................................................................................... 28

8.1.2

Point to Multi-Point Link................................................................................... 29

8.2

Automatic Power Control ....................................................................................................... 31

Summary of Contents for GWS-3000





























Search results

Summary of Contents for GWS-3000

Reviews:

Related manuals for GWS-3000

Brands by name

Popular brands

6Harmonics GWS-3000, Operating Manual

Search results

Summary of Contents for GWS-3000

Reviews:

Related manuals for GWS-3000

Brands by name

Popular brands