6Harmonics GWS-3000 Operating Manual Download Page 2

Page: 2 / 31

1. Table of Contents

1. Table of Contents

................................................................................................................................. 2

Revision Control..................................................................................................................................... 4

3. FCC Regulatory Information .............................................................................................................. 5

4. Introduction ....................................................................................................................................... 6

Product Overview ........................................................................................................................... 7

4.1 External Dimensions of the radio module.................................................................................... 7

System Diagram ............................................................................................................................. 8

Software Environment..................................................................................................................... 8

6.1 Overview ..................................................................................................................................... 8

6.2 Node Initialization ........................................................................................................................ 9

6.3 Setup and Communicate with Host Board................................................................................... 9

6.3.1 User Interfaces ...................................................................................................... 9

6.3.2 Serial Port ............................................................................................................... 9

6.3.3 SSH ..................................................................................................................... 10

6.4

Configure the IP Address of the Nodes ................................................................................. 12

6.5 Image burn and upgrade ........................................................................................................... 12

6.5.1 Burn image for first time....................................................................................... 12

6.6.2 Upgrade Image .................................................................................................... 13

6.6.3 Upgrade the application ....................................................................................... 13

6.7 Configurations ............................................................................................................................ 13

6.7.1 Configure GWS Node Mode as BTS or CPE ....................................................... 13

6.7.2 Wireless Configuration........................................................................................ 16

6.7.3 Radio turn on (For non database application) ....................................................... 18

6.7.4 Check channel number (For non database application)........................................ 18

7.0 User Commands ............................................................................................................................ 18

7.1 help command............................................................................................................................ 19

7.2 setchan command ..................................................................................................................... 19

7.3 getchan command..................................................................................................................... 20

7.4 txresume command................................................................................................................... 20

7.5 txoff command.......................................................................................................................... 20

7.6 gettxstatus command ................................................................................................................ 20

7.7 getrxstatus command ................................................................................................................ 20

7.8 settxpwr command ................................................................................................................... 20

7.9 gettxpwr command .................................................................................................................... 21

7.10 rfinfo command ...................................................................................................................... 21

7.11 u command ............................................................................................................................ 21

7.12 d command ........................................................................................................................... 21

7.13 setchanlist command............................................................................................................. 22

7.14 getchanlist command .............................................................................................................. 22

7.15 getrxgain command................................................................................................................. 22

7.16 setrxgain command ................................................................................................................ 23

7.17 monitor command .................................................................................................................. 23

7.18 setinstaller command ............................................................................................................. 23

7.19 getinstaller command .............................................................................................................. 23

7.20 setsubchanlist command....................................................................................................... 24

7.21 getsubchanlist command........................................................................................................ 25

Summary of Contents for GWS-3000





























Search results

Summary of Contents for GWS-3000

Reviews:

Related manuals for GWS-3000

Brands by name

Popular brands

6Harmonics GWS-3000, Operating Manual

Search results

Summary of Contents for GWS-3000

Reviews:

Related manuals for GWS-3000

Brands by name

Popular brands