3M SCP716W Installation Manual Download Page 2

Page: 2 / 22

Assembly and Installation Guide

3M™ SCP700 Series Mobile Stand

Contact 3M Mobile Interactive Solutions Division with any questions -

Phone: (800) 328-1371

www.mmm.com/meetings

Table of Contents

Important Notice ................................................................................................................. 3

Warranty; Limited Remedy; Limited Liability ................................................................... 3

Safety Information .............................................................................................................. 4

Parts List ............................................................................................................................. 6

Installation Tools ................................................................................................................. 6

Preface ................................................................................................................................. 7

Caster Wheel Installation .................................................................................................... 8

Gas Shock Installation ........................................................................................................ 8

Shelf Assembly (Optional) .................................................................................................. 9

Support Pole Installation ................................................................................................... 10

Attaching the Back Support Assembly and Back Plate .................................................... 10

Upper and Lower Horizontal Support Arm Installation ................................................... 11

Install Mobile Cart Stabilizer ........................................................................................... 12

Attach Hanger to Projection Board ................................................................................... 13

Projector Installation ......................................................................................................... 14

Route Control Cable ......................................................................................................... 15

Attaching to the Stand ....................................................................................................... 15

Route Cables in Stand ....................................................................................................... 16

Attach the Projector .......................................................................................................... 17

Assemble the Arm Extension ............................................................................................ 18

Safety Pin Installation ....................................................................................................... 19

Technical Specification

..................................................................................................... 20

The 3M logo and 3M are trademarks of the 3M Company. Other trademarks used herein are the properties of their respective

owners.

Summary of Contents for SCP716W






















Search results

Summary of Contents for SCP716W

Reviews:

Related manuals for SCP716W

Brands by name

Popular brands

3M SCP716W, Installation Manual

Search results

Summary of Contents for SCP716W

Reviews:

Related manuals for SCP716W

Brands by name

Popular brands