6
Lad-Saf
™
Flexible Cable Ladder Safety System Components, Figure 1
A
Top Bracket
D
Cable Guide
G
Frontal D-Ring
B
Cable
E
i-Safe RFID Tag
H
Full Body Harness
C
Cable Sleeve
F
Bottom Bracket
Lad-Saf
™
X2 Detachable Cable Sleeve Components, Figure 2
(“
i
” is Back of Sleeve, “
ii
” is front of Sleeve)
A
Cable (not component)
D
Handle/Energy Absorber/
Fall Indicator
G
Locking Lever
J
Carabiner
M
ID Label
B
Upper Roller
E
Sleeve Body
H
Lower Roller
K
Gravity Stop
N
RFID Tag
C
Rotating Side Plate
F
Logo Label
I
This way UP Arrow
L
Cam
Cable types approved for use with the Lad-Saf
™
X2 Detachable Cable Sleeve
ANSI, CSA
Cable Part Number
CE
Cable Part Number
DESCRIPTION
9500098
9500098
Cable, 3/8, 7 x 19, Galvanized
9500099
9500099
Cable, 3/8, 7 x 19, 304 Stainless Steel
9500396
9500396
Cable, 3/8, 1 x 7, Galvanized
9500397
9500397
Cable, 3/8, 1x 7, 304 Stainless Steel
9501591
9501591
Cable, 5/16, 7 x 19, Galvanized
7240212
Cable, 8mm, 1 x 19, 316 Stainless Steel
1.2 LIMITATIONS:
The Lad-Saf
™
X2 Detachable Cable Sleeve must be used with a DBI-SALA approved ladder safety system.
Use only a 5/16 inch (8 mm) or 3/8 inch (9.5 mm) diameter solid core cable with the Detachable Cable Sleeve. The ladder
safety system must have a maximum angle of 15° from vertical.
The minimum temperature that the Detachable Cable Sleeve, including a rigid anchor line, is approved for is -22°F
(-30°C).
The Lad-Saf
™
X2 Detachable Cable Sleeve must be directly connected to an approved full body harness
with the attached carabiner (Figure 2, J). Do not use connection devices other than the carabiner or
snap hook that is part of the Lad-Saf
™
X2 Detachable Cable Sleeve.
NOTE:
ANSI A14.3 and OSHA 1926.1053 state that the length of connection between the carrier and
attachment point must not exceed 9 inches (23 cm).
2.0 SYSTEM REQUIREMENTS
2.1
COMPATIBILITY OF COMPONENTS AND SUBSYSTEMS:
This equipment is designed for use with DBI-SALA approved
components and subsystems. The use of non-approved components and subsystems (i.e. harnesses, lanyards, etc.) may
jeopardize compatibility of equipment, and could affect the safety and reliability of the complete system. If you have
questions on the installation or suitability of this equipment for your application, contact DBI-SALA.
COMPATIBILITY WITH CLIMB ASSIST SYSTEMS:
The DBI-SALA
Lad-Saf™ Ladder Safety Systems, including the DBI-
SALA Lad-Saf™ Detachable Cable Sleeves
, are designed for use with DBI-SALA approved climb assist systems. The use of
any other type of climb assist system, including a powered climb assist system, may be incompatible with the
Lad-Saf™
Ladder Safety System and Detachable Cable Sleeves
, and could create a serious safety hazard for the user. Do not use
non-DBI-SALA climb assist systems without first consulting a competent person and/or a qualified person at your worksite
for approval. If you have additional questions about compatibility, please contact 3M Technical Services.
ANSI Z359.1-2007 Safety Requirements for Personal Fall Arrest Systems, Subsystems and
Components, requires a competent person and/or a qualified person to “ensure that systems
assembled from components and subsystems made by different manufacturers meet the
requirements of this standard.”
Failure to follow these instructions may result in serious injury or death to users of the Lad-Saf
™
Ladder Safety System and Detachable Cable Sleeve.
2.2
COMPATIBILITY OF CONNECTORS:
(See Figure 4)
Use only supplied connectors.
Connect carabiner (
A
) to frontal D-Ring (
B
).
2.3
MAKING CONNECTIONS:
(See Figure 5)
Capital Safety snap hooks and carabiners
should not
be connected:
A.
To a D-Ring to which another connector is attached.
B.
In a manner that would result in a load on the gate.
C.
To each other.
Ensure all connectors are fully closed and locked
.