3M Dynatel 2250M Operator'S Manual Download Page 57

Page: 57 / 65

78-8130-6150-0-F

•  Program one or multiple receivers to best suit specific user configurations
•  Load an alternate language into the receiver
•  Utilize the 3M

™

iD Marker utility to:

− Create templates for writing data to iD markers, or create Trace Templates for

GPS path tracing when connected to a GPS device.

− Download iD marker data that has been written or read by the receiver for

documentation databases.

Embedded in the desktop software is the most current software for the receiver, which

affords the user the option of upgrading the unit without returning the unit to the

3M Service and Repair Center.
Please refer to the operating instructions included with the software.

22. Self Test Of Receiver

Menu [6] + >>More [SK:4] + Self Test [SK:7]

This operation performs a self-test on the receiver.
The receiver will display current information about the unit (model number, serial

number, software revision, and hardware revision).
1. Press

Run

[SK] to start the self test.

− A status bar will appear while the self test is running.

− Results will appear on the display when the test is complete.

− Press Exit [SK] to return to the Menu.

23. Product Description And Optional Accessories

A. Product Description

T= Transmitter

R=Receiver

Transmitter Output Power: 3W=3 Watt. 5W=5 Watt, 12W=12 Watt

Direct Connect Cable Clip Size: For 3 Watt and 5 Watt Transmitters only:
C= Communication Clip only; U=Utility Clip only;
For 12 Watt Transmitters only: CU=Communication and Utility Clips; W=Utility Clip only

U=US Version; E=Export Version

iD=Locates electronic markers, including read/write iD Marker capability

2250M=Cable/Pipe Locator; 2273M=Cable/Pipe/Fault Locator

2250M
2273M

Example: 2273M-iD/UCU12W-RT
Description:

2273M Cable/Pipe/Fault Locator / iD capability; U.S. version;

Communication and Utility direct connect cables (clips); 12-Watt Transmitter; Receiver

and Transmitter included.

Summary of Contents for Dynatel 2250M


































































Search results

Summary of Contents for Dynatel 2250M

Reviews:

Related manuals for Dynatel 2250M

Brands by name

Popular brands

3M Dynatel 2250M, Operator'S Manual

Search results

Summary of Contents for Dynatel 2250M

Reviews:

Related manuals for Dynatel 2250M

Brands by name

Popular brands