3M Dynatel 2250M Operator'S Manual Download Page 15

Page: 15 / 65

78-8130-6150-0-F

[13] Fault Finding Direction Indicators:

Corresponds to the Earth Contact Frame

(A-Frame) probe (leg) colors.

[l4] External Jack:

Port to connect cables from external devices such as the earth frame

(A-Frame), a second Dyna-Coupler, or a toning coil.

[15]

Serial Port:

RS232 port to connect the receiver to a PC via serial cable or USB-to-

serial adapter cable.

[16] Earphone Jack:

Will fit standard 1/8" (3.175 mm) mini-jack mono earphone plug

(not included).

4. Menu Displays

A. Main Menu

When the Menu [6] button is pressed, the Main Menu display appears.
The function appears on the display above each soft key.

1. Write Mode:

System used to write information to iD Markers

2. Data/Template:

Displays marker history and

template creation/selection displays:

a. Read History

– 100 memory locations for

Read iD Markers

b. Write History

– 100 memory locations for

Written iD Markers

c. User Templates

– Create and edit iD

templates for iD Markers (max = 32)

d. Trace Templates

– Create and edit

templates used to identify path (max = 5)

Summary of Contents for Dynatel 2250M


































































Search results

Summary of Contents for Dynatel 2250M

Reviews:

Related manuals for Dynatel 2250M

Brands by name

Popular brands

3M Dynatel 2250M, Operator'S Manual

Search results

Summary of Contents for Dynatel 2250M

Reviews:

Related manuals for Dynatel 2250M

Brands by name

Popular brands