3M Dynatel 2250M Operator'S Manual Download Page 50

Page: 50 / 65

78-8130-6150-0-F

B. Write History [SK]

Menu [6] + Data Templat [SK:2] + Write History [SK:2b]

1. Select the marker data to be viewed by pressing

the up/down arrows [SK].

2. Press

Write Details

[SK] to view all data that

was sent to the marker.

3. Press

Write History

[SK] to return to the list of

written data.

4. Press

Exit

[SK] to return to Data/Template

review display.

For additional information concerning writing to 3M

™

iD Markers, refer to

www.3M.com/dynatel

Instruction Manual M-Series Locator PC Tools.

18. GPS Operation

A. Activation Key

To activate the GPS compatibility in the receiver, an activation key must be entered

into the receiver. You must have at least version 14.0 of the receiver software. For the

receiver to transmit information to the GPS device for use in GIS mapping applications

(see

F. Sending iD Marker Data to GPS (Capture-Transmit Mode / Mode 2)

), the

hardware version must be 5.0 or higher. (See

B. Serial Number and Software Version

The software upgrade and activation key can be obtained from the website

www.3M.com/dynatel

for no charge. You will be asked to enter the serial number of the

receiver and a few other informational items in order to receive the GPS activation key.
Upgrade the software of the receiver using the desktop software, if necessary, using:

™

Dynatel

™

PC Tool Kit. Enter the GPS activation key on the receiver (See

Inputting

the GPS Activation Key

, Section 18C).

B. Serial Number and Software Version

Menu [6] + >>More [SK:4] + Self Test [SK:7]

The model number, software version, hardware version, and serial number of the

receiver are available on the Self Test display. The Self Test Mode can also be run from

this screen by pressing Run [SK].

C. Inputting the GPS Activation Key

Menu [6] + COM Setup [SK:3]

Initially, when the COM key is pressed, and an attempt is made to enable any selection

other than

, the display below will appear and you will be prompted to input the

activation key that you have obtained from the website. This will have to be performed

only one time to enable the GPS interface.

Summary of Contents for Dynatel 2250M


































































Search results

Summary of Contents for Dynatel 2250M

Reviews:

Related manuals for Dynatel 2250M

Brands by name

Popular brands

3M Dynatel 2250M, Operator'S Manual

Search results

Summary of Contents for Dynatel 2250M

Reviews:

Related manuals for Dynatel 2250M

Brands by name

Popular brands