3M Dynatel 2250M Operator'S Manual Download Page 48

Page: 48 / 65

78-8130-6150-0-F

6. The operator may select

User Edit

in order to

‘type’ the modification, or

Delete Row

to remove

the entire row from the template, or select

Show

All

to display a list of common compressed

terms.

Note: Using a common compressed term requires

less memory in the marker.

7. Select an option from the list by pressing the up/

down arrows [SK]. Press

Locate/OK

[5].

8. If

User Edit

is selected, the following display

will appear.

9. Move the boxed cursor to the ‘back arrow’

and press

Select

[SK] to delete the entry to be

modified.

10. Move the boxed cursor by pressing the left/right

arrows [SK], or the Up/ Down Arrow [SK], to

move the cursor to the next row.

11. Press

Select

[SK] to enter the alphanumeric

character.

− Entry will appear at the top of the display.

12. Press

Locate/OK

[5] when entry is complete.

13. If

Show All

is selected, the following display

will appear.

14. Select a common compressed term from the list

by pressing the up/down arrows [SK].

15. Press

Locate/OK

[5]. The modification will

automatically populate the marker template.

16. Reading iD Markers

The operator can retrieve the data from the iD marker by pressing Read [SK] on the

Marker Locate display.
The receiver tip should be lowered to the ground to reach maximum read depth.
If more than one 3M

™

iD Marker of the same utility is detected, the receiver will read

the first marker and display the data from the marker.

Summary of Contents for Dynatel 2250M


































































Search results

Summary of Contents for Dynatel 2250M

Reviews:

Related manuals for Dynatel 2250M

Brands by name

Popular brands

3M Dynatel 2250M, Operator'S Manual

Search results

Summary of Contents for Dynatel 2250M

Reviews:

Related manuals for Dynatel 2250M

Brands by name

Popular brands