3M Dynatel 2250M Operator'S Manual Download Page 47

Page: 47 / 65

78-8130-6150-0-F

− The receiver will ask if the user wants to

permanently lock the marker data.

9. Select

[SK] or

Yes

[SK]. The receiver will

write the data to the marker. (

See note below

10. After writing to the iD Marker is completed, the

following will be displayed.

Note: Once the marker data has been locked, the information contained on the marker

is PERMANENT. Choosing to permanently lock the marker data is irreversible. Once

the data is locked it can not be overwritten. Assure that the data that is being written is

correct before proceeding.

A. Modifying Marker Data to be Written

To alter the information to be written into the marker
1. Press

Menu

[6] +

Write Mode

[SK:1].

2. Select a template from the list on the display to be written into the marker by

pressing the up/down arrows [SK] to highlight the preferred template. ‘Last

Written/Read’ is the most recent data that was written to a marker by the receiver.

3. Press

View/Edit

[SK].

4. Press the up/down arrows [SK] to highlight the

information to change.

5. Press

Modify

[SK]. The percentage displayed in

the upper right portion of the display indicates

the remaining memory available on the marker.

Summary of Contents for Dynatel 2250M


































































Search results

Summary of Contents for Dynatel 2250M

Reviews:

Related manuals for Dynatel 2250M

Brands by name

Popular brands

3M Dynatel 2250M, Operator'S Manual

Search results

Summary of Contents for Dynatel 2250M

Reviews:

Related manuals for Dynatel 2250M

Brands by name

Popular brands