background image

78-0015-0557-3-B 

15 

5.9 

Before the network has a laser light source feeding 
your connector, inspect the fiber end face with 
3M™ 200X View Scope 6365-VS if you have one. 
If the fiber end face looks acceptable per photos to 
the right, then protect it with a dust cap, or insert 
into its adapter. If the connector needs rework, 
proceed to Section 6.0. 

 
Caution reminder: Never look directly into the end of a 
fiber or connector when connected to a laser light source 
using the naked eye or a microscope. 

Chips or cracks inside the ½ diameter circle are not allowed 

Acceptable chip 

Unacceptable chip, 

needs rework 

Unacceptable crack, 

needs rework 

Dirty, needs 

cleaning 

Alcohol on fiber, 

re-dry 

Alcohol on 

ferrule, re-dry 

Thread caught, re-

clean with a twist 

UPC only photo: forgot 

to spray water, needs 

rework 

Forgot to use lapping 

film, needs rework 

Thin black line is visible 

Ideal, clean fiber end face 

Light grey 

Dark grey 

No line, just grey to white 

Fiber is missing, go to step 6.1 

Cleave nick mark 

Rough 

edge 

Not polished, restart at step 5.1 

Summary of Contents for Crimplok 6702-50 50 um MM



















Reviews: