![background image](http://html1.mh-extra.com/html/3m/anie-jooltool/anie-jooltool_user-manual_443955010.webp)
ABRASIVES, BACKPADS & CUSHIONS
Remove all protective film from new ABRASIVE before applying it onto the BACKPAD.
NOTE:
Adhesive cures rapidly when ABRASIVE is applied onto BACKPAD.
ANIE’S TIP:
At first, apply the ABRASIVE very lightly onto the BACKPAD. This will give you the
opportunity to make corrections and adjust the SEE-THRU™ pattern alignment if necessary
before the adhesive cures. Press firmly to adhere when the SEE-THRU™ alignment is correct.
HOW TO REMOVE LEFTOVER ADHESIVE FROM BACKPADS:
When changing worn abrasives,
you can leave the leftover adhesive on the BACKPAD as the new abrasive will likely fuse
with it upon use. If you prefer a clean surface, you can remove leftover adhesive by
dabbing with the sticky side of your old abrasive or sticky tape. Do NOT use solvents!
ALWAYS
change ABRASIVE if it is damaged, torn or is excessively worn.
3M
recommends to
DISCARD
an abrasive once it’s been r
emoved/unstuck
from the BACKPAD
as the ADHESIVE on the Abrasive is designed for SINGLE APPLICATION ONLY.
Failure to follow this rule can potentially cause property damage and/or personal injury!
NEVER
use an ABRASIVE if it is not adhering to the BACKPAD.
NEVER
apply ABRASIVES on BACKPAD when wet.
NEVER
use disc if the ABRASIVE has been improperly installed onto the BACKPAD.
Improperly installed abrasive increases risk of property damage and/or personal injury!
NEVER
cut, change, or distort the shape of the SEE-THRU ™ design on the abrasive.
ALWAYS
place abrasive on the FLAT (BOTTOM) surface of the BACKPAD.
ALWAYS
install abrasives on the BACKPAD by aligning correctly with the SEE-THRU™ design.
ALWAYS
press firmly to ensure full adherence between ABRASIVE and BACKPAD.
HOW TO SAFELY INSTALL AND OPERATE
ALWAYS
turn JOOLTOOL “OFF” before installing/changing BACKPADS or ACCESSORIES.
NEVER
install BACKPADS while the motor is “ON”. This can cause personal injury.
Follow all safety instructions shown below
Warning: motor rotation is COUNTER-CLOCKWISE
Use for ABRASIVES that require CUSHION BACKING
(ex: Polishing Diamond, Trizact™ and other FINE Abrasives)
ALWAYS
apply CUSHIONS
BEFORE
applying ABRASIVES.
ALWAYS
remove all protective film from CUSHIONS
before applying it onto the BACKPADS.
ALWAYS
apply CUSHIONS to flat surface of BACKPADS.
NOTE:
DO NOT APPLY CUSHIONS UNDER FELT DISC OR SCRATCH-ERASER ABRASIVES.
ALWAYS
install BACKPADS with ABRASIVE side DOWN.
ALWAYS
tighten your BACKPADS snuggly onto the spindle before use.
ALWAYS
use GENUINE JOOLTOOL™ BACKPADS & ORIGINAL spindle.
This will guarantee that your discs will be perfectly centered and give you optimal results.
NEVER
use third-party (non-JOOLTOOL™ brand) Spindles.
NEVER
use damaged or cracked BACKPADS as they may break apart during use, potentially causing injury.
NEVER
place workpiece on top or the side of spinning disc. The disc can eject workpiece and may cause loss of control.
ALWAYS
Turn the Jooltool “OFF” if excessive vibration occurs during use.
See “TROUBLESHOOTING”
p.30
ABRASIVE
(CUSHION)
BACKPAD
1
2
3
CUSHIONS - SETUP & SAFETY
ABRASIVES - RECOMMENDED SETUP & SAFETY
RO
TATIO
N
Toll Free: 1-85-JOOLTOOL
p.10
Buy supplies at WWW.JOOLTOOL.COM