3DHISTECH PANNORAMIC SCAN RX 1.1 User Manual Download | Manualshive

Page: 25 / 165

background image

PANNORAMIC® SCAN RX 1.1

INSTALLATION

NOVEMBER 18, 2021

24

FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES.

2

Installation

Warning!

The installation of Pannoramic® SCAN RX must be carried out by a trained professional! In
any other case the warranty will be automatically voided. The supplier or distributor is not
liable for any damages caused by an installation carried out by an unauthorized person.

Only qualified service assistants are allowed to install the hardware and software. The
product is ready for use after installation.

Caution!

Make sure that the device is placed so that there is enough space for ventilation and for safe
and efficient operator maintenance.

Caution!

If the temperature of the location where the scanner is operated is much lower than the
temperature of the equipment (for example, the device is brought in from an outer storage,
or has been transported to the site), please leave enough time to normalize the
temperature differences before operating the device within the safe range.

2.1

Operation system of the control computer

The scanner is operable with a Fujitsu CELSIUS M7010 as the control computer that runs Windows
10 (see table

Control computer, minimum system requirements

in chapter

10 Technical Data

Third-party antivirus programs can affect the operation of the software, but we are not
responsible for any resulting problems.

«
...
23
24
25
26
27
...
»

Summary of Contents for PANNORAMIC SCAN RX 1.1






































































































































































Reviews:

No comments

Related manuals for PANNORAMIC SCAN RX 1.1

Brand: Canon Pages: 124

imageFORMULA DR-M160

Brand: Canon Pages: 56

Brand: Canon Pages: 2

2050C - DR - Document Scanner

Brand: Canon Pages: 2

Microfilm Scanner 350II

Brand: Canon Pages: 62

imageFORMULA ScanFront 300

Brand: Canon Pages: 28

Brand: Leuze Pages: 15

ONETOUCH 7400 USB

Brand: Visioneer Pages: 2

OneTouch 5300 Series

Brand: Visioneer Pages: 40

Brand: Xerox Pages: 143

Brand: Allflex Pages: 44

Brand: I.R.I.S. Pages: 17

Brand: GMC Pages: 145

OpticFilm 7200i SE

Brand: Plustek Pages: 2

Brand: Plustek Pages: 39

Brand: kaarta Pages: 95

Brand: Oce Pages: 136

Brand: Halo Photonics Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands