3DHISTECH PANNORAMIC SCAN RX 1.1 User Manual Download

Page: 141 / 165

PANNORAMIC® SCAN RX 1.1

USING PROFILES

NOVEMBER 18, 2021

140

FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES.

Using Profiles

Notice:

Saved profile settings cannot be applied if using a different type of Pannoramic® scanner.

If you want to scan a group of slides, it is advised to save your settings previously in a
profile and continue scanning in Automatic mode. You can save the following settings in a
profile:

Scan Mode

•

Brightfield

•

Fluorescent

Scan Options

•

Focus frequency (in Fluorescent mode)

•

Focus frequency (in Brightfield mode)

•

Compression procedure

•

Use of a fixed compensation image (in Brightfield mode

–

ON/OFF)

•

Use of Save focus quality (ON/OFF)

•

Use of Stitching (ON/OFF)

Determination of the area to be scanned

•

Use of automatic threshold specimen

•

Use of specimen threshold value

•

Use of marker pen threshold and specimen threshold values

•

Remove coverslip function (ON/OFF)

•

Use of scan everything within marked area (ON/OFF)

•

Filling of holes (ON/OFF)

•

Use of removing specks according to the set value (ON/OFF)

•

Use saved scan area

•

Use selection box (ON/OFF)

Summary of Contents for PANNORAMIC SCAN RX 1.1






































































































































































Search results

Summary of Contents for PANNORAMIC SCAN RX 1.1

Reviews:

Related manuals for PANNORAMIC SCAN RX 1.1

Brands by name

Popular brands

3DHISTECH PANNORAMIC SCAN RX 1.1, User Manual

Search results

Summary of Contents for PANNORAMIC SCAN RX 1.1

Reviews:

Related manuals for PANNORAMIC SCAN RX 1.1

Brands by name

Popular brands