3D Systems projet mjp 2500, User Manual, Page: 90 / 92

BASIC REGULATIONS
3D Systems has tested this printer to electromagnetic emission and immunity standards. These standards are designed to mitigate interference caused or
received by this printer in a typical office environment.
United States
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy. If it is not installed and used in accordance with these instructions, it may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his/her own expense.
Changes or modifications to this equipment not approved by 3D Systems can void the authority of the user to operate this equipment.
Canada
Ce dispositif est conforme aÌ la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux
conditions suivantes: (1) le dispositif ne doit pas produire de brouillage preìjudiciable, et (2) ce dispositif doit accepter tout brouillage rec?u, y compris un
brouillage susceptible de provoquer un fonctionnement indeìsirable.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
European Union
CAUTION: This is a Class A product. In a domestic environment, this product can cause radio interference in which case the user could be
required to take adequate measures.
In order to allow the equipment to operate in close proximity to Industrial, Scientific and Medical (ISM) equipment, the external radiation from the ISM equipment
may have to be limited or special mitigation measures taken.
Changes or modifications to this equipment not approved by 3D Systems can void the authority of the user to operate this equipment.
EC DECLARATION OF CONFORMITY
La Déclaration de CE de Conformité
We, 3D SYSTEMS, INC. herewith declare that the following described 3D printer system in our delivered version complies with the basic safety and health
requirements of the EC Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006, based on its design and type, as brought into
circulation by us. In case of alteration of the 3D printer system, not agreed upon by us, the declaration will lose its validity.
Nous, 3D SYSTEMES, INC. ci-joint déclarer que le suivre a décrit la 3D printer system dans notre version livrée se conforme à la sûreté fondamentaux et aux
conditions de santé des Directive de CET 2006/42/EC du Parlement européen et du Conseil 17 Mai 2006, a basé au dessous sa conception et son type, comme
amené dans la circulation par nous. En cas du changement de la 3D printer system, pas consenti sur par nous, la déclaration perdra sa validité.
Description of the 3D printer system:
La description de la 3D printer system:
STEREOLITHOGRAPHY APPARATUS
ProJet 2500 Production Modeling Systems
3D printer system type:
Usiner le type: Year of Manufacture:
Année de Fabrication
Serial Number:
Numéro de série
Applicable EC Directives:
Les Directives applicables de CE:
DIRECTIVE 2006/42/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCILof 17 May 2006 on machinery, and
amending Directive 95/16/EC (recast), EMC Directive (2004/108EC)
Applicable Harmonized EC Standards:
Les Normes de CET Harmonisé applicables:
EN/IEC61010-1, 3rd Edition; E, EN/IEC60825-1:2007, EN 61000-6-2:2005; EN6000-6-4:2007