manualshive.com logo in svg

3D Systems projet mjp 2500, User Manual, Page: 55 / 92

Share
Download
3D Systems projet mjp 2500 User Manual Download Page 55

REMOVING PIXIE DUST FROM UV ASSEMBLIES (LEFT AND RIGHT)

Removing Pixie Dust from UV Assemblies (right and left)

Over time, the UV assemblies accumulate a buildup of pixie dust (light coating of material particles) that will need to be wiped off with a lint free cloth and
isopropyl alcohol.

Right UV Assembly

Select 

Tools > Diagnostics > Inspect Planarizer Ducts

1.

​

The print engine will be centered over the platform allowing user access to the UV lamp assembly.

2.

Place a paper towel underneath carriage to catch any material that is loosened during the wiping process.

3.

Reach underneath to the right UV lamp assembly and wipe pixie dust using a lint free cloth moistened with isopropyl alcohol.

4.

 NOTE: Always wear nitrile gloves and either a protective sleeve or lab coat when performing this procedure to protect skin from

exposure to uncured materials.

​ NOTE: When wiping the right UV assembly use care not to touch printhead.

Summary of Contents for projet mjp 2500





























































































Reviews:

No comments