3D Systems DMP Flex 350 Original Instructions Manual Download Page 43

Page: 43 / 45

A/C

Argon Gas

min 16° C (60° F)

27° C (80° F)

max

Atmosphere

CHILLER

Chiller power

•

Separate from

DMP Flex 350

• 200 to 230 VAC

• 50/60 Hz

• 15 kVA

• C

ustomer supplied/installed

Argon

• Customer supplied/installed

Room oxygen monitor

• Recommended

• Customer supplied/installed

Room temperature

setpoint and stability

• Set temperature between 18° C and 24° C (65° F and 75° F)

• Temperature should be constant to ±2° C (± 5° F)

Coolant Hoses

▪

Included with 3D Systems-supplied chiller

▪

1/2" barbed hose fitting

Argon cylinders

▪

Use a high volume pressure reducer

▪

Connect cylinders with auto-switching

manifold to ensure constant argon

supply during build

Bulk Argon tank

▪

Option for high argon demand sites

Compressed Air

Air Conditioning

• Required

•

Do not install vent directly above process station!

Compressed air

• Customer supplied/installed

Electrical cable

• Customer supplied/installed

Transformer

(optional)

Control cabinet

power panel

• 400 VAC

• 50/60 Hz

• 10 kVA

FACILITY REQUIREMENTS POSTER - COMPACT INSTALLATION

Summary of Contents for DMP Flex 350














































Search results

Summary of Contents for DMP Flex 350

Reviews:

Related manuals for DMP Flex 350

Brands by name

Popular brands

3D Systems DMP Flex 350, Original Instructions Manual

Search results

Summary of Contents for DMP Flex 350

Reviews:

Related manuals for DMP Flex 350

Brands by name

Popular brands