manualshive.com logo in svg

3Com H3C S7503E-S CHASSIS, Installation Manual, Page: 57 / 200

Share
Download
3Com H3C S7503E-S CHASSIS Installation Manual Download Page 57

 

1-50 

Panel and LEDs 

Figure 1-28 shows the front panel of the LSQ1SRPD0. 

Figure 1-28 

Front panel of the LSQ1SRPD0 

 

(1) CF card slot and CF card status LED 

(2) Console port 

(3) 10/100Base-TX management port and its LEDs 

(4) Power module and fan status LEDs  

(5) LPU status LEDs  

(6) ACTIVE LED of LSQ1SRPD0  

(7) RESET button 

 

On-board interfaces 

z

 

CF card slot 

The CF card slot can accommodate a standard CF card (Type I or Type II), where you can store host 
software and logs and thus upgrade software conveniently. The CF card is hot swappable.  

z

 

Console port 

Using an RJ-45 connector, the console port can be connected through a common asynchronous serial 
cable directly to a computer for system debugging, configuration, maintenance, management, and host 
software loading, or to a modem for remote system debugging, configuration, maintenance and 
management. 

Table 1-86 

Specifications of the console port 

Item 

Specifications 

Connector type 

RJ-45 

Number of connectors 

1 

Interface standard 

Asynchronous EIA/TIA-232 

Baud rate 

115200 bps (9600 bps by default) 

Transmission distance 

15 m (49.21 ft.) 

Functions 

z

 

It can be connected to an ASCII terminal. 

z

 

It can be connected to a serial port of a local or remote (through a 

pair of modems) PC running terminal emulation program. 

 

z

 

10/100Base-TX management port 

Using an RJ-45 connector, the 10/100Base-TX management port can be connected to a local PC for 
switch program loading and switch debugging, or connected to a remote NMS for remote management. 

Table 1-87 

Specifications of the 10/100Base-TX management port 

Item 

Specifications 

Connector type 

RJ-45 

Number of connectors 

1 

Transmission speed and type 

10/100 Mbps, half/full duplex 

Summary of Contents for H3C S7503E-S CHASSIS









































































































































































































Reviews:

No comments