manualshive.com logo in svg

3Com H3C S7503E-S CHASSIS, Installation Manual, Page: 111 / 200

Share
Download
3Com H3C S7503E-S CHASSIS Installation Manual Download Page 111

 

3-4 

z

 

If there is a grounding strip in the Ethernet switch installation environment, attach one end of the 
yellow-green protection grounding cable to the grounding screw of the grounding strip and fasten 
the captive nuts. The grounding cable of a switch shall be connected to the project ground of the 
equipment room. 

Figure 3-3 

Connect the protection grounding cable to the grounding strip 

Power input

Ethernet 

Switch

Grounding strip

Protection  grounding cable

Grounding screw

Ethernet 

Switch

Ethernet 

Switch

 

 

z

 

If there is no grounding strip but earth nearby and the grounding body is allowed to be buried, you 
can simply hammer an angle iron or steel pipe no shorter than 0.5m into the earth. In this case, the 
yellow-green protection grounding cable should be welded with the angle iron (steel pipe) and the 
joint should be processed against eroding. 

Figure 3-4 

Connect the protection grounding cable to the grounding body nearby 

Power input

Ethernet Switch

Grounding screw

Angle steel

Ground

Protection  grounding cable

 

 

z

 

If there is no grounding strip and no grounding body can be buried, the AC-powered Ethernet 
switch can be grounded through the PE wire of the AC power supply. In this case, make sure that 
the PE wire of the AC power supply has been well grounded at the power distribution room or AC 
power supply transformer side. 

Summary of Contents for H3C S7503E-S CHASSIS









































































































































































































Reviews:

No comments