manualshive.com logo in svg

3Com H3C S7503E-S CHASSIS, Installation Manual, Page: 25 / 200

Share
Download
3Com H3C S7503E-S CHASSIS Installation Manual Download Page 25

 

1-18 

The PSR6000-ACV power module provides system power and PoE power. In Figure 1-17 the switch 
indicated by callout 6 is used to control the system power and the socket indicated by callout 5 is used 
for system power input, while the switch indicated by callout 2 is used to control the PoE power and the 
sockets indicated by callout 8 are used for PoE power inputs. 
To provide PoE power by the PSR6000-ACV, you need to 

z

 

Switch on the system power and make sure that the system power output is normal 

z

 

Switch on the PoE power and make sure that one of the three PoE power inputs is alive 

The PoE output power of the PSR6000-ACV depends on the number of PoE power inputs that are 
selected as needed. For detailed technical specifications, refer to Table 1-13. 
 

 

z

 

If the system power input and multiple PoE power inputs are used at the same time, the input 
voltage must be the same, that is, either 110 VAC or 220 VAC, but not be intermixed. 

z

 

Keep the PoE switch in the off position unless the device is equipped with appropriate PoE-capable 
cards and needs to offer PoE supply. 

 
On the right of the panel are the system power input LED (SYS IN), system power output LED (SYS 
OUT), system power fan LED (SYS FAN), PoE input LEDs (PoE IN1, PoE IN2, and PoE IN3), PoE 
output LED (PoE OUT), and PoE power fan LED (PoE FAN). For the descriptions of these LEDs, refer 
to section 7.2.6  “Troubleshooting PSR6000-ACV.” 

Table 1-13 

Technical specifications of the PSR6000-ACV power module 

Item 

Specifications 

Rated voltage range 

100 VAC to 240 VAC, 50 Hz or 60 Hz 

Maximum input current for each socket 

16 A 

Maximum system output current 

117 A 

Maximum PoE output current 

100 A 

1150 W (110 VAC) 

Maximum system output power 

1400 W (220 VAC) 
1200 W (110 VAC) 

One PoE input 

1800 W (220 VAC) 
2400 W (110 VAC) 

Two PoE inputs 

3600 W (220 VAC) 

3600 W (110 VAC) 

Maximum PoE 

output power 

Three PoE inputs 

5300 W (220 VAC) 

Dimensions (H × W × D) 

128 × 196 × 380 mm (5.04 × 7.72 × 14.96 in.) 

Operating temperature 

0°C to 45°C (32°F to 113°F) 

Storage temperature 

–40°C to +70°C (–40°F to +158°F) 

 

Summary of Contents for H3C S7503E-S CHASSIS









































































































































































































Reviews:

No comments