2B Technologies AQSync Operation Manual Download Page 60

Page: 60 / 74

H. Maintaining and Troubleshooting the AQSync

Model AQSync Air Quality Monitoring Station Manual Rev. A-1

Air pump is not drawing
sufficient flow.

Air flow should be greater
than 1.4 L/min. If flow is
lower, check for leaks. If
there are no leaks, replace air
pump.

Instrument has a large
offset

Internal heated NO

scrubber

is exhausted or contaminated.

Contact 2B Technologies
about replacement of the
internal heated NO

scrubber.

Instrument always reads
close to zero for NO

concentrations.

Solenoid valve cable is not
properly connected to circuit
board.

Internal heated NO

scrubber

is exhausted or contaminated.

Reattach solenoid valve
cable to circuit board.

Contact 2B Technologies
about replacement of the
internal heated NO

scrubber.

Table H.4. Error Codes of the NO

/NO/NO

Module

The following tables list the hexadecimal codes and their corresponding error
definitions. The first table lists the errors if there were only one error, while the second
table lists all of the possible error combinations with their definitions.

Single Errors

Error byte

Definition

No errors

Scrubber temp out of range. Temp is either > 113 degrees or < 110.

Pressure control out of range by > 1 mbar

Cell flow out of range (< 1200 or >1600)

Ozone flow out of range (<30 or >110)

Cell voltage out of range (<0.1V or >2.4V)

Ozone Generator voltage out of range (< 0.01V or >2.4V)

Combination Errors

Error Byte

Definition

Scrubber Temp and Cell Voltage

Scrubber Temp and Cell Flow

Scrubber Temp, Cell Flow, and Cell Voltage

Cell Voltage, and Ozone Generator Voltage

Cell Flow, Cell Voltage, and Ozone Generator Voltage

Scrubber Temp and Cell Voltage

Cell Flow and Cell Voltage

Scrubber Temp, Cell Voltage, and Ozone Generator Voltage

Scrubber Temp, Cell Flow, and Ozone Generator Voltage

Summary of Contents for AQSync











































































Search results

Summary of Contents for AQSync

Reviews:

Related manuals for AQSync

Brands by name

Popular brands

2B Technologies AQSync, Operation Manual

Search results

Summary of Contents for AQSync

Reviews:

Related manuals for AQSync

Brands by name

Popular brands