ZURN Aqua-FIT Serio Series, Инструкция по установке, эксплуатации, обслуживанию и каталог запасных частей

Страница: 9 / 9

FV563 Rev. - 12/2/14
Page 9
OPERATION
1.) Invisible light rays are continually emitted from the faucet
sensor.
2.) When the user’s hands come into range of the sensor’s
detection zone (factory set at approximately 6”), the beam is
reflected back to the sensor’s reciever and converted to a low
voltage electrical signal activating a solenoid valve.
3.) After the user removes their hands, the absence of reflected
light stops the low voltage electrical signal, closing the valve.
The circuit automatically resets for the next user.
4.) If an object is in view continuously for thirty seconds, the
faucet will automatically shut off. The faucet will remain off until
the object is removed. After the object is removed, the faucet
functions normally.
Aqua-FIT
TM
is a trademark of Zurn Industries, LLC.
Printed in the U.S.A.
TROUBLESHOOTING GUIDE
SPECIFICATION
Voltage:
Sensor Range:
Operating Water
Pressure:
Ambient
Temperature:
Operational Water
Temperature:
Aerator:
6 VDC
(4 “AA” Alkaline)
6” Approximate from Water Outlet
20-80 psi
32ºF to 122ºF (0ºC to 50ºC)
35°F to 140°F (2°C to 60°C)
1.5 GPM Vandal-Resistant (Standard)
ZURN INDUSTRIES, LLC.
♦ ♦ ♦ ♦ ♦
COMMERCIAL BRASS OPERATION
♦ ♦ ♦ ♦ ♦
5900 ELWIN BUCHANAN DRIVE
♦ ♦ ♦ ♦ ♦
SANFORD NC 27330
Phone: 1-800-997-3876
♦ ♦
♦ ♦ ♦
Fax: 919-775-3541
♦ ♦
♦ ♦ ♦
World Wide Web: www.zurn.com
In Canada: ZURN INDUSTRIES LIMITED
♦ ♦ ♦ ♦ ♦
3544 Nashua Drive
♦ ♦ ♦ ♦ ♦
Mississauga, Ontario L4V1L2
♦ ♦ ♦ ♦ ♦
Phone: 905-405-8272 Fax: 905-405-1292
POTENTIAL SITUATIONS POSSIBLE CAUSES SUGGESTED SOLUTION TIPS
Solenoid is not connected properly Place hands in sensor range. If clicking occurs, solenoid is connected
correctly. If no clicking occurs, disconnect the sensor cable from the
black box and w ait 15 sec bef ore reconnecting. Once reconnected try
activating again.
Batteries are low on pow er Change out batteries
Sensor and electronic connector cable has
bent or broken pins Check to see if pins are missing, bent, or broken. If yes, then the
electronic box needs replaced
Solenoid is lodged w ith debris Check solenoid for debris and clean if necessary and reassemble
If f aucet is hardw ired, could have voltage
range issues Check voltage levels and adjust if necessary to f all w ithin
recommended ranges.
Sensor lens could be obstructed by
environmental factors such as high ref lective
surf aces or bright lighting conditions If this is the case, then adjust the dip sw itch settings f or sensor
resolution per the diagram in the installation manual (sw itches 7 and 8)
Sensor lens could have surface damage,
scratches, or deposit build ups f rom chemical
cleaners Inspect the sensor lens underneath the spout tip. May require cleaning
(damp rag) or replacement
Remove the battery tray and inspect for visual signs of rust, w ater,
debris. Replace battery tray if these symptoms are f ound.
Remove battery tray, if no visual signs can be detected, try using a
metallic object to tap the coils to exhaust any fault charges. Reassemble
Sensor f aucet does not
activate af ter initial installation Sensor lens may not have had enough time to
calibrate prior to a user or target trying to
initiate activation Disconnect the sensor and electronic box cables and w ait for 15
seconds. Reconnect the cables, but allow f or another 15 seconds
before placing hands or a target w ithin the sensor range. Y ou should
hear a click of the solenoid once calibration is complete.
Solenoid is lodged w ith debris Check solenoid for debris and clean if necessary and reassemble
Sensor and electronic connector cable has
bent or broken pins Check to see if pins are missing, bent, or broken. If yes, then the
electronic box needs replaced
If this is the case, then adjust the dip sw itch settings f or sensor
resolution per the diagram in the installation manual (sw itches 7 and 8)
Loosen the mounting nuts and try sliding the f aucet back in the lavatory,
sink, or counter top holes back tow ards the w all and retightening. Could
be detecting the grid drain in the sink bow l.
Mounting hardw are is not tightened suf ficiently
(faucet shank, electronic box, supply hoses,
etc) Check and ensure the nuts and joints are tight and secure from the
supply stop all the w ay to the f aucet shank.
Missing the w asher located in the solenoid box
nut w here it assembles to the f aucet shank. Make sure w ater supply stops are shut of f. Check to ensure the
w asher is installed. If not, need to replace w ith a new w asher.
Sensor f aucet is leaking
underneath the sink or
counter
Sensor f aucet is not
activating or running
Coils in battery tray are promoting a voltage
drain
Faucet runs continuously
(longer than the selected time-
out that is programmed)
Sensor f aucet is experiencing
random activations w hen a
user or target is not w ithin
sensing range Sensor lens could be obstructed by
environmental factors such as high ref lective
surf aces or bright lighting conditions