Zte ZXDSL 9210 (V3.1) Скачать руководство пользователя страница 173

Страница: 173 / 182

Erro! Estilo não definido.

B-3

Standard No.

Standard Name

IETF RFC1661

Point-to-Point Protocol (PPP)

RFC1213

Management Information Base of TCP/IP-based Internet Network Management: MIB-II.

K. McCloghrie, M.T. Rose.Mar.1 1991

RFC1643

Definitions of Managed Objects of Ethernet Interface Types. F. Kastenholz. July 1994

RFC1757

Remote Network Monitoring MIB. S. Waldbusser. February 1995

RFC2021

Remote Network Monitoring MIB Version 2 Use SMIv2. S. Waldbusser. January 1997

RFC2074

MIB Protocol Identifier for Remote Network Monitoring. A. Bierman, R. Iddon. January

1997FF

RFC2613

Remote Network Monitoring Management of Switching Network MIB Extended Version

1.0. R. Waterman, B. Lahaye, D. Romascanu, S. Waldbusser. June 1999

RFC2665 Ethernet-like

MIB

RFC0768 (1990)

UDP protocol

RFC0791 (1990)

IP protocol

RFC0793 (1990)

TCP protocol

RFC0854 (1990)

TELNET protocol

RFC0855 (1990)

Telnet Protocol Options Specifications

RFC0858 (1990)

Telnet Advance Suppress Options

RFC0894 (1990)

Standards for Transmission of IP Packets over Ethernet

RFC1157 (1990)

Simple Network Management Protocol (SNMP)

RFC1213 (1991)

Network Management Information Base of TCP/IP-based Internet: MIB-II

RFC1332 (1992)

IPCP protocol

RFC1631 (1994)

IP Network Address Translator (NAT)

RFC1661 (1994)

PPP

RFC1990 (1996)

PPP Multilink Protocol

RFC1944 (1996)

Performance Test Methods of Network Interconnection Equipment

ANSI/IEEE Std 802.1D 1998

Edition

Media Access Control (MAC) Bridge

IEEE Std 802.1Q 1998

Virtual Bridge LAN

IEEE Std 802.1ad2000

Multiple Link Section Aggregation

IEEE Std 802.2 1998

Logic Link Control

IEEE Std 802.3 1998 Edition

Carrier Monitoring Multiple Access Mode with Collision Detection and Definition of

Physical Layer

IEEE Std 802.3ab 1999

Physical Layer Parameters and Regulations for Transmission of Gigabit Ethernet over 4

Pairs of Category 5 Balanced Twisted Pair 1000BASE-T

Содержание ZXDSL 9210 (V3.1)























































































































































































Результаты поиска

Содержание ZXDSL 9210 (V3.1)

Отзывы:

Похожие инструкции для ZXDSL 9210 (V3.1)

Бренды по названию

Популярные бренды

Zte ZXDSL 9210 (V3.1), Техническое руководство

Результаты поиска

Содержание ZXDSL 9210 (V3.1)

Отзывы:

Похожие инструкции для ZXDSL 9210 (V3.1)

Бренды по названию

Популярные бренды