Zte ZXDSL 9210 (V3.1) Скачать руководство пользователя страница 31

Страница: 31 / 182

2-1

2 System Structure

Based on the R&D background of the ZXDSL 9210 product and its application

environment in the network, this chapter introduces the key functions and system

characteristics of the ZXDSL 9210 system. Meanwhile, this chapter lists the standards

applicable to the product, including ADSL standards, ATM standards, Ethernet

standards, and national standards.

2.1 Brief Introduction to the System

2.1.1 Background

ZTE has developed ZXDSL 9210 (V3.1) Broadband Universal Access Equipment

(called ZXDSL 9210 or 9210 for short) to meet users’ requirements. This product

employs the VDSL and ADSL technologies. In the VDSL technology, the FDM and

Quadrature Amplitude Modulation (QAM) technologies are combined to transmit voice

and high-speed digital signals over an ordinary copper twisted pair. When the

uplink/downlink rate reaches 10M and the line width is 0.4 mm, the maximum

transmission distance amounts to one kilometer. In the ADSL mode, existing ordinary

telephone lines (copper cable twisted pairs) are used. The Frequency Division

Multiplexing (FDM) and Discrete Multi-Tone (DMT) technologies are combined to

provide sufficient broadband capacity and to transmit voice and data services

simultaneously without any interference between them. ZXDSL 9210 supports both

symmetric and asymmetric uplink/downlink data transmission, such as high-speed

Internet access, VOD, remote monitoring & detection, and high-speed LAN

interconnection. The equipment is applicable to telecom carriers, Access Service

Providers (ASPs), and Internet Service Providers (ISPs). It improves utilization of

ordinary telephone twisted pairs and is an important device to implement the "last

mile" access of broadband and multiple services.

The ZXDSL 9210 system employs IP-based networking modes. Broadband network is

generally a 3-layer system architecture: Access layer, convergence layer, and core layer.

The access layer functions, completed by the 9210 access equipment (including the

central office and the subscriber premises), provide three access modes (ADSL access,

Содержание ZXDSL 9210 (V3.1)























































































































































































Результаты поиска

Содержание ZXDSL 9210 (V3.1)

Отзывы:

Похожие инструкции для ZXDSL 9210 (V3.1)

Бренды по названию

Популярные бренды

Zte ZXDSL 9210 (V3.1), Техническое руководство

Результаты поиска

Содержание ZXDSL 9210 (V3.1)

Отзывы:

Похожие инструкции для ZXDSL 9210 (V3.1)

Бренды по названию

Популярные бренды