Zte ZXDSL 9210 (V3.1) Скачать руководство пользователя страница 79

Страница: 79 / 182

Chapter

Erro! Estilo não definido.

4-17

EICMA provides four 10/100M Ethernet electrical interfaces and four 100M

single-mode optical interfaces in compliance with IEEE 802.3u via FEC subcard.

EICMB provides four 10/100M Ethernet electrical interfaces and four 100M

single-mode optical interfaces in compliance with IEEE 802.3u via FNC subcard.

The EICMC provides 4-channel 10/100M Ethernet electrical interfaces and 4-channel

100M single-mode optical interfaces in compliance with the IEEE 802.3u Standards

via the FEC subcard. Besides, EICMC provides 4-channel 10/100M Ethernet electrical

interfaces and 4-channel 100M Ethernet optical interfaces in compliance with the IEEE

802.3u Standards via the FNC subcard.

4.2.6.2 Operating Principles of EICM

EICM implements Ethernet user access and provides uplink ports. This function is

implemented by Layer 2 Ethernet uplink subboard (FEC) or enhanced Ethernet

subboard (FNC). These two kinds of subcards have almost the same operating

principles, as shown in Fig. 4.2-8.

Backplane

CPU

HDLC controller

HDLC channel

G.Link bus

Ethernet processor

Ethernet module

Fig. 4.2-8 Operating Principles of Ethernet Interface Subcards

EICM consists of the CPU, HDLC controller, Ethernet processor, and Ethernet module,

and various modules implement the following functions:

1. The CPU module completes the control over boards and the communication

with SCBF;

2. The HDLC module is used to manage HDLC channels.

Содержание ZXDSL 9210 (V3.1)























































































































































































Результаты поиска

Содержание ZXDSL 9210 (V3.1)

Отзывы:

Похожие инструкции для ZXDSL 9210 (V3.1)

Бренды по названию

Популярные бренды

Zte ZXDSL 9210 (V3.1), Техническое руководство

Результаты поиска

Содержание ZXDSL 9210 (V3.1)

Отзывы:

Похожие инструкции для ZXDSL 9210 (V3.1)

Бренды по названию

Популярные бренды