Zontes ZT310-X, Руководство по обслуживанию

Страница: 52 / 119

8、FRONT FORK COMPONENT 51
CHK
ADJ
NO. PART NO. PART NAME QTY CAUTION
1154200-005000 ZT310-R Throttle refueling line Delphi EFI
1154200-016000 ZT310-R Throttle refueling line (bosch) Bosch EFI
1154200-006000 ZT310-R Throttle return line Delphi EFI
1154200-015000 ZT310-R Throttle return line (bosch) Bosch EFI
3 1224200-016000 ZT310-R Line clamp 1
4 1224100-051000 0 Flame retardant tie (black 2.5×100) 1
5 1244100-042000 ZT250-R Right handlebar rubber sleeve 1
6 Right handlebar switch 1
7 1250205-031091 GB70.1M6×30 (stainless steel) 2
8 Right handlebar auxiliary switch 1
PROCEDURE:
●
Disassemble the throttle line
Use an open-end wrench to turn the nut
②
of the throttle refueling line
⑴
or the oil return line
⑵
upside down, turn the
nut
④
downwards out of the adjusting pipe
①
; rotate the turntable on the throttle valve clockwise, and turn the cylindrical
joint of the fuel line from the turntable Remove; then move the adjustment tube upwards over the bracket
③
on the throttle
valve and pull outwards to separate the core from the bracket. Similarly, remove the oil return line.
Open the card of the line clamp
⑶
slightly, remove the throttle cable from the slot, and cut off the cable tie
⑷
.
Loosen the bolts
⑺
with the Allen tool; remove the sub switch
⑻
and the right brake rocker arm assembly
⑼
in the
direction of the arrow and lock the bolt
⑺
. Always keep disc brake main pump
⑨
high to prevent air from entering the oil
circuit.
Hold the right hand switch
⑹
with your hand and remove the bolts
⑦
and
⑧
before removing the bolt
⑥
. Switch the
upper and lower parts of the switch.
Remove the throttle cable from the right hand and remove the rubber sleeve
⑸
from the core turntable
⑩
, and then
remove it from the cable hole in the lower part of the switch.
●
Install the throttle line
First pass the throttle cable into the cable hole in the lower part of the switch. Fit the cylindrical connector of the throttle
cable into the turntable
⑩
on the right hand gripper
⑸
. Return the oil return line card to the limit slot provided on the fuel
line. Use a hexagon socket tool to lock the bolt
⑦
to a torque of
⑧
to 10 Nm. The switch mounting hole is slightly twisted
a few times for the rear bolt
⑧
and the bolt
⑥
is locked after observing the positioning hole and the direction of the lower
part of the switch
⑹
. Finally, tighten the bolt
⑧
and tie the tie
⑷
. Cut off the excess. Reset the sub switch and rocker
assembly and note the symbol on the alignment switch. Install the throttle cable into the slot of the hub clamp
⑶
. Use an
open hand to turn the nut
②
of the throttle refueling line
⑴
or the return line
⑵
up to the end, and turn the nut
④
downwards to the adjustment pipe
①
. Put the oil return line into the bracket
③
, and fit the connector into the turntable
⑤
.
Put the oil line into the bracket
③
, then turn the turntable
⑤
to a certain angle, and then insert the connector. Refer to the
method of adjusting the gap to adjust the throttle line clearance; after adjusting the left and right direction of rotation, there
should be no change in idle speed and flexible reset. Lock nuts
②
and
④
.
1 1
2 1
Fig.3 FRONT FORK
COMPONENT
Replace the throttle line